Twin Otter Extended
Support for the Aerosoft Twin Otter Extended
983 topics in this forum
-
- 5 replies
- 1.3k views
-
- 6 replies
- 1.3k views
-
- 4 replies
- 1.3k views
-
- 1 reply
- 1k views
-
- 1 reply
- 1.8k views
-
- 1 reply
- 1k views
-
- 1 reply
- 919 views
-
- 2 replies
- 2.3k views
-
- 9 replies
- 2.7k views
-
- 12 replies
- 2.2k views
-
- 7 replies
- 2.1k views
-
- 5 replies
- 4.3k views
-
- 2 replies
- 1.3k views
-
- 6 replies
- 1.9k views
-
- 3 replies
- 910 views
-
- 0 replies
- 956 views
-
- 5 replies
- 1.3k views
-
- 4 replies
- 907 views
-
- 3 replies
- 1.6k views
-
- 8 replies
- 1.1k views
-
- 8 replies
- 2.5k views
-
- 10 replies
- 3.2k views
-
- 2 replies
- 2.2k views
-
- 2 replies
- 2k views
-
- 9 replies
- 3.5k views
.thumb.jpg.08d64886eb408fcfef99bb2df2dcf260.jpg)
Announcements
-
Popular Topics
-
-
Latest Posts
-
You are Welcome Ed, I am close to hanging my hat and allowing new and younger talent to take over. I hardly get time to sim anymore due to work - so I loosing my touch -
Fellow Captains July's screenshot contest should be a breeze as you perform this task with every departure. so let's get creative and show some of your best "CLIMBING OUT" captures. Arrow: Departing TVSM Mustique in the Grenadines (MSFS 2020)
Please login to display this image.
TBM 940: Departing S43 in Washington State (MSFS 2020)Please login to display this image.
Piper Seneca: climbing out of TRPG - John Osborne (MSFS 2020)Please login to display this image.
Piper Seneca: Gear up - Climbing out of TVSM (MSFS 2020)Please login to display this image.
Austrian A321: Climbing out of LOWW (X-Plane 11)Please login to display this image.
AmeriJet Boeing 727: Cleaned and and climbing out TLPC Vigie, heading to TDPD Melville Hall (MSFS 2020)Please login to display this image.
Fenix A320: Climbing out over New York City (MSFS 2024)Please login to display this image.
Southwest 737-700: Maintaining runway heading Climbing to FL230Please login to display this image.
Please login to display this image.
A321 Neo: Climbing out of FLL from runway 27Please login to display this image.
Sorry - got carried away wit the images, but you get the jest of the contest requirements. As Always - All participants are ONLY allowed 1 image if you post more than one - ONLY the first entry will be judged and the others deleted. Users are allowed to change their posted image up until the time frame allowing you to do so expires. If you fail to post an image based on the theme of the month, it is very likely that the image will not be considered during "judgment day". This a multi-sim platform for your "FLIGHT" images as we welcome FS2009, FSX, Prepar3D, MSFS 2020, MSFS 2024, X-Plane 9 - 12, DCS, Infinite Flight and even AeroFly images. Good Luck to ALL. -
Hello. Okay that helped. I found that a switch on the left yoke handle was also mapped to the elevator trim. So after un-mapping the switch and making sure that only the trim wheel was mapped to the trim wheel, there was some improvement. The trim no longer jittered when I used the trim wheel. However, responsiveness of the trim wheel remains about the same. When I lined a "bump" on the trim wheel on the sim's dashboard and turned the trim wheel on the Bravo Throttle quadrant, I had to turn the Bravo Trim wheel 4-8 full revolutions to make the trim wheel in the sim move one "bump" when adjusting the nose up and 6-11 full revolutions to adjust down one bump. This was sticking my finger on the white section and spinning it slowly. When I'm in flight, that isn't possible due to the proximity of the Alpha Yoke and, if you excuse the expression, "That just ain't right." So now that the "jitters" are gone and the wheel is reacting, how do you make it actually move at least closely to that in the sim. After a few test flights using different planes, it was the same in all planes. It simply isn't responsive enough to use in flight. How can I adjust it to be more responsive? Again, thank you for all your help. Awaiting your response. -
By Rob Ainscough · Posted
Looks like I found my answer here going a few years back: I’ll check my EXE.XML files tonight. BUT, this begs the question, why? The installer should be doing an UPDATE not INSERT. If existing entry exists don’t add another one. This implies that anytime I buy and install an Aerosoft airport it will keep INSERTING (not updating) this entry in my EXE.XML file? Other than generating a lot of support tickets/traffic, I can’t see leaving this “as is” to be beneficial? Rob. -
By Rob Ainscough · Posted
I purchased OSLO for MSFS/MSFS 2024 and install to both platforms since they exist on my computer. When i start MSFS 2024, I get two dialog/windows that pop up saying “VDGS has already started”? I only started getting these pop up messages AFTER installing OSLO. What is VDGS? Why is it needed? How do I prevent these windows from popping up? Rob.
-
![Aerosoft Team [Inactive Account]](https://forum.aerosoft.com/uploads/monthly_2023_09/Aerosoft_Social_Media_Profilbild_Neu23.thumb.jpg.03721825e6a434ed4af0c8b2b73a5898.jpg)