CumulusX!

Discussion related to all aspects of this exciting new program that puts thermals in FSX and creates ridge lift using CCS slope files.

166 topics in this forum

  1. Pinned topics
  2. Download CumulusX!

    • 0 replies
    • 19840 views
  3. Topics
    • 3 replies
    • 2701 views
  4. P3Dv4?

    • 5 replies
    • 3939 views
    • 3 replies
    • 2167 views
    • 3 replies
    • 2481 views
    • 10 replies
    • 2707 views
    • 5 replies
    • 3890 views
  5. Online in P3Dv3?

    • 8 replies
    • 4439 views
  6. CumulusX and P3D V3

    • 2 replies
    • 3335 views
  7. Tow plane in P3D

    • 5 replies
    • 4608 views
  8. For Newbies Like Me

    • 1 reply
    • 3749 views
    • 3 replies
    • 4347 views
    • 2 replies
    • 3991 views
    • 5 replies
    • 5368 views
    • 4 replies
    • 4068 views
    • 1 reply
    • 4836 views
    • 10 replies
    • 5170 views
  9. CumulusX Activation

    • 17 replies
    • 4846 views
    • 5 replies
    • 4998 views
    • 6 replies
    • 5346 views
  10. Smart tow in P3D

    • 1 reply
    • 3921 views
    • 2 replies
    • 3713 views
    • 1 reply
    • 3951 views
    • 17 replies
    • 4850 views
    • 5 replies
    • 5412 views
  • Posts

    • you have 2 ways to do that: 1- restore original p3d shader from the Action menu in PTA 2-reinstall p3d content 
    • Recently purchased the SimCheck A300 and the A300 FMC Update.   Using the Flightsim Estonia migration tool, I successfully installed the A300 in P3DV3. The A300 operates as expected.   I then installed the A300 FMC Update. I ran P3DV3 and loaded the DHL A300 but the FMC did not appear.   I then discovered the location of the manual for the FMC Update. Under the heading "First Start" is the following:   To add the FMC to aircraft, run the „Texture installer“ and update the panel.   I located the Texture Installer and ran it. Before the installer itself appeared, a dialog box appeared requesting to install .Net 3.5. I accepted this request and .Net 3.5 (and others) installed successfully.   The Texture Installer then appeared but I couldn't find commands that had something to do with "update the panel". I assume the purpose in running it was to make sure that the necessary versions of .Net are installed.   After closing the TI, I ran P3DV3 and loaded the DHL A300. Still no FMC. (Note: the SimConnect A300 Settings popup has an entry reading "SimCheck A300 SP3FMC").   Any suggestions as to what I might try next to active the FMC Update?   Thank you          
    • I just wanted to provide a bit more info if someone else will be looking through here with the same question :). 
    • Also, if you're using an older Navigraph data base, you might find it created a sub-folder in the correct folder, and you just have to move the contents of the sub-folder to the main folder (basically up one level).   Best wishes.  
    • if you use ORBX vector - check the AES tool and look for a Valancia AFCAD in Mytraffic (B2_LEVC.bgl?)