English
General talk on Aerosoft and Products. Please do NOT use this forum for any support questions, use the dedicated support sections for that.
If you posted and cannot find your message anymore, we probably have moved it for you. Just check the forum layout and look for the most likely section and you will find your post.
Subforums
-
- 11.8k
- posts
-
- 21.9k
- posts
6776 topics in this forum
-
Pinned topics
-
- 500 replies
- 117.8k views
-
- 576 replies
- 117.7k views
-
- 13 replies
- 732 views
-
- 2 replies
- 4.1k views
-
- 525 replies
- 140.1k views
-
- 0 replies
- 1.5k views
-
- 15 replies
- 12.5k views
-
- 0 replies
- 2.9k views
-
- 0 replies
- 12.3k views
-
- 0 replies
- 16.9k views
-
- 24 replies
- 18.8k views
-
- 0 replies
- 16.8k views
-
Topics
-
- 1 reply
- 37 views
-
- 1 reply
- 102 views
-
- 1 reply
- 204 views
-
- 3 replies
- 150 views
-
- 1 reply
- 125 views
-
- 2 replies
- 127 views
-
- 0 replies
- 107 views
-
- 9 replies
- 901 views
-
- 4 replies
- 308 views
-
- 3 replies
- 159 views
-
- 1 reply
- 205 views
-
- 1 reply
- 113 views
-
- 14 replies
- 224 views
-
Popular Topics
-
-
Latest Posts
-
Check that Hardware Accelerated GPU Scheduling is turned ON in Windows. Early on in MSFS, many recommended turning this off for the exact reasons that are laid out in this thread. Nvidia's latest drivers (maybe a few versions before, didnt pay attention) explicitly say this should be turned ON for best performance, especially if you have a later gen card -
Das LEMD Mesh muss raus. Dafür machst du ja das Ortho. -
Which specific approach and transition? I will check. -
Making that switch work 100 percent accurately would require the ability to disable the inputs from external hardware controllers (specifically, the rudder axis) from within the running simulator, and that is currently not possible in MSFS. For the same reason, ailerons and elevators will not move in the real aircraft without hydraulics, but they will in the sim. External hardware controllers for pitch, roll and yaw are always “live” even when the aircraft is powered completely down. However, the nose wheel steering switch does have an effect. If you look at an external view, you will see that with the switch off, the nose wheel does not move with rudder pedal inputs, but with the switch on it does move. This is not just an animation. The effect of nose wheel tire friction is part of the flight model, and with the switch on, it is much easier to make sharp turns at low taxi speeds (without having to use a lot of engine power), than with the switch off.
-
By Johnnyo411 · Posted
I am having trouble with the FMS as well. I put in a flight plan, check for discontinuity, execute and verify all waypoints are in correctly and in the right order. In this example I was flying out of YYZ and hit direct to kepta and exec and some random waypoint shows up nothing to do with my flight plan. I manually flew the aircraft until past kepta and then hit direct to bmpah and then the flight plan broke still with the same random waypoint but now a disconnect after bmpah but nothing wrong in the FMS as far as waypoints. Tried on a few other airports and the same thing. In this example I loaded the flight plan manually but have also tried loading a company route generated by simbrief and still the same thing. any help would be appreciated John Orton
-
