Deputy Sheriffs masterhawk 799 Posted October 27, 2020 Deputy Sheriffs Share Posted October 27, 2020 8 minutes ago, AirbusPilotWB! said: Q: Hm, ok. Is the indication of the x and y axis as expected in the game controller dialog? A: Yes. No green bars with thrust levers in full reverse position. Approx. 33% at idle position, 50% at CL position and 100% in TOGA. (% = green bars). Full reverse: Please login to display this image. Idle: Please login to display this image. CL: Please login to display this image. TOGA: Please login to display this image. Q: Is there an option to delete calibration in P3D? Just another possibility. A: No. 'Remove Calibrations' is only available in 'Raw Input' mode. Direct Input: Please login to display this image. Please login to display this image. Raw Input: Please login to display this image. Please login to display this image. Ok, looks good so far. Have you set Throttel 1 and 2 to the X and Y axis and the general Throttle is empty? Also not asigned on another controller? Please login to display this image. Link to comment Share on other sites More sharing options...
AVFC 9 Posted October 27, 2020 Share Posted October 27, 2020 10 minutes ago, masterhawk said: Ok, looks good so far. Have you set Throttel 1 and 2 to the X and Y axis and the general Throttle is empty? Also not asigned on another controller? Please login to display this image. Yes: Please login to display this image. Link to comment Share on other sites More sharing options...
Deputy Sheriffs masterhawk 799 Posted October 27, 2020 Deputy Sheriffs Share Posted October 27, 2020 15 minutes ago, AirbusPilotWB! said: Yes: Please login to display this image. Ok...now I’m out of ideas. Except these two: 1. And you activated the TCA Quadrant setting in the configurator? And only the Quadrant setting, not the stick setting!? 2. Like suggested by another user. Remove quadrant uninstall drivers and reboot. Then install again. Link to comment Share on other sites More sharing options...
JeyhanOsman 2 Posted October 27, 2020 Share Posted October 27, 2020 Hello, Its now working for me. This is what I did: I have the thrustmaster TCA drivers installed for the quadrant. Firstly I opened the AS configurator and activated support for TCA quadrant only. Then assigned the eng 1 and 2 throttle axis individually, calibrated the thrust levers in P3D by moving them through full range and then leaving the thrust levers centred ( CLB detent) before saving. Hopefully it works for others too. Link to comment Share on other sites More sharing options...
AVFC 9 Posted October 27, 2020 Share Posted October 27, 2020 15 minutes ago, masterhawk said: Ok...now I’m out of ideas. Except these two: 1. And you activated the TCA Quadrant setting in the configurator? And only the Quadrant setting, not the stick setting!? 2. Like suggested by another user. Remove quadrant uninstall drivers and reboot. Then install again. I even tried to install the old TM driver version, but without any change.. Link to comment Share on other sites More sharing options...
AVFC 9 Posted October 27, 2020 Share Posted October 27, 2020 34 minutes ago, masterhawk said: Ok...now I’m out of ideas. Except these two: 1. And you activated the TCA Quadrant setting in the configurator? And only the Quadrant setting, not the stick setting!? 2. Like suggested by another user. Remove quadrant uninstall drivers and reboot. Then install again. Re-installed latest drivers and rebuild the configuration file. All good now. Thank you for support. Please login to display this image. Link to comment Share on other sites More sharing options...
Brittanix 12 Posted October 27, 2020 Share Posted October 27, 2020 1 hour ago, AirbusPilotWB! said: Re-installed latest drivers and rebuild the configuration file. All good now. Thank you for support. Please login to display this image. This has finally worked for me, incldung the correct detents (by reseting using CTRL + CAPS LOCK). However, it only works if I set Engine 1 throttle to X Axis and Engine 2 throttle to Y Axis. If I set the complete "Throttle Axis" then it will not work. Im using P3Dv5 btw. Link to comment Share on other sites More sharing options...
Deputy Sheriffs masterhawk 799 Posted October 31, 2020 Deputy Sheriffs Share Posted October 31, 2020 On 10/27/2020 at 10:08 PM, TAP729 said: Until the radio / linda problem is solved, it is possible to get the previous version again. I say this because in the previous version it was working. Waiting for a reply Kind regards Carlos Godinho On 10/29/2020 at 3:36 AM, TAP729 said: With the 1.4.1.1 Stable release is this problem solved ???? : "In the Vrinsight / Airbus version, the radio frequencies can no longer be set." Waiting for reply Kind regards Carlos Godinho 11 hours ago, passicfc94 said: Same Problem with vrinsight Boeing Gents, this is a topic covering TCA support, even if it is in the general (no support) section. Your problem is already part of a topic in the support section. And there is the Info, that next week we will check the Radio Problem. You can always install the latest full installer without running the updater. I hided your Posts, to keep this topic clean, so that other users can find the relevant infos. Link to comment Share on other sites More sharing options...
LionAir 5 Posted October 31, 2020 Share Posted October 31, 2020 Goodday all, Following all the tips as described above all works like a charm, except...... When I switch of the engines - by toggling down the engine 1 switch - everything goes fine - engine 1 stops but by toggling down the engine 2 switch - engine 2 stops also but at the same time all power is switching off, so the complete cockpit and screens are dark and out. I have looked in the key-assigments in TCA - Q-eng 1+2 but no buttons are assigned for i.e. external power or batteries. In the configuration I have only quadrant ticked.... I hope someone can get point me into the right direction. BTW I have Aerosoft Airbuses 318/319/320/321 Prepar3d - V 4.5 with latest HF Windows 10 with latest update Thrustmaster TCS sidestick + Quadrant Have a nice evening and stay healthy rgrds, Gerrit Link to comment Share on other sites More sharing options...
Helmut Brandt 57 Posted October 31, 2020 Share Posted October 31, 2020 Before switching off the engines APU switched on ? Link to comment Share on other sites More sharing options...
LionAir 5 Posted October 31, 2020 Share Posted October 31, 2020 yes, I have done the following (only for testing, not a complete flight with procedures ....) Selected A320 CFM Select "taxi-state" so that the engines were on Engines switches to on APU on switch of engine 1 - no problem switch of engine 2 - engine goes out but electric power also Do I forget or oversee something ?? Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51561 Posted October 31, 2020 Aerosoft Share Posted October 31, 2020 Gents, please check the titl;e of this section. It clearly states NO SUPPORT. Please use the correct sections of the forum so the right people read your comments. When you post them incorrectly they have a massive chance of just gettings lost. Link to comment Share on other sites More sharing options...
LionAir 5 Posted October 31, 2020 Share Posted October 31, 2020 No problem, what is the best section? I have not seen any topic for the Thrustmaster tca (maybe I have overseen it) Thanks Link to comment Share on other sites More sharing options...
Deputy Sheriffs masterhawk 799 Posted October 31, 2020 Deputy Sheriffs Share Posted October 31, 2020 7 minutes ago, LionAir said: No problem, what is the best section? I have not seen any topic for the Thrustmaster tca (maybe I have overseen it) Thanks For your problem with the Airbus...Airbus Support section. Link to comment Share on other sites More sharing options...
LionAir 5 Posted October 31, 2020 Share Posted October 31, 2020 It's not a problem with the Airbus but the Thrustmaster TCA Throttle Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51561 Posted November 2, 2020 Aerosoft Share Posted November 2, 2020 Still, for use in the Airbus, feel free to use those sections. Link to comment Share on other sites More sharing options...
Alex97490 3 Posted November 9, 2020 Share Posted November 9, 2020 how about the CPDLC update? Link to comment Share on other sites More sharing options...
Deputy Sheriffs masterhawk 799 Posted November 9, 2020 Deputy Sheriffs Share Posted November 9, 2020 51 minutes ago, Alex97490 said: how about the CPDLC update? Please, this is a TCA topic. The update takes a lot more time, then expected. Just wait. Link to comment Share on other sites More sharing options...
sholay 5 Posted November 10, 2020 Share Posted November 10, 2020 Eee, so far not even re-install helped. The throttle in the sims (P3Dv4.5 and MSFS) jumps all over the range, when physical lever is in Idle it's full thrust in the sim etc. Now in th AS CRJ it works smoothly but the range is like central 50% of the range, no full throttle no idle and obviously no reverse. I wonder if there's anyone here how got this working out of the box or with straightforward calibration. I understand for some it worked by uninstalling TM drivers, reboot, installing TM drivers back and calibration in the P3D and/or MSFS. Is this correct statement? & Link to comment Share on other sites More sharing options...
LionAir 5 Posted November 10, 2020 Share Posted November 10, 2020 Goodday, Does somebody know when the TCA Airbus Throttle Add-On units are coming available? I have asked Thrustmaster-support but until now without any response (I mean the units for flaps/speedbrake) thanks for info and stay healthy...... Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51561 Posted November 10, 2020 Aerosoft Share Posted November 10, 2020 The only thing we know is that they are expected this year. Link to comment Share on other sites More sharing options...
LionAir 5 Posted November 10, 2020 Share Posted November 10, 2020 Okay, thanks. We will wait and see...... Link to comment Share on other sites More sharing options...
Deputy Sheriffs Herman 1591 Posted November 12, 2020 Deputy Sheriffs Share Posted November 12, 2020 As Mathijs noted over a week ago, this really belongs in the Airbus support section, even though it concerns the new TM Airbus thrust lever. Since all the issues point to the Airbus, that's where this is moved. Hopefully, that will also keep it from getting hijacked with irrelevant questions. Since the "moved" note goes away in a couple of days, I'll put a placeholder post where it once was pointing to this one. Link to comment Share on other sites More sharing options...
HB-JHM 20 Posted November 12, 2020 Share Posted November 12, 2020 does it works with A330? Link to comment Share on other sites More sharing options...
LionAir 5 Posted November 12, 2020 Share Posted November 12, 2020 On 11/10/2020 at 11:41 AM, Mathijs Kok said: The only thing we know is that they are expected this year. At this moment we do not have an ETA on when these accessories will become available for acquisition. But their official release date will be made publicly on our press release page with at least 2 months before they will become available for acquisition through us or through our official partners: Finally get a answer from Thrustmaster support. It seems these units are not available very soon Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.