Ca. 274 MB warten auf den Download.   Release Date: January 10, 2026 Aircraft Airbus A330-300 Fixed the display of QNH on the PERF APPR PAGE of the MCDU (XPD-17627) Always allow the entry of values on the PERF APPR PAGE regardless of the current flight stage (XPD-17634) Fixed an issue where selecting heading mode would disable ALT CRZ (XPD-17673) Fixed several drawing issues on the ND Improved autopilot turn rate Enabled CLR button on the transponder Several other minor improvements ATC & Radio Fixed missing ATIS for some airports (XPD-17630) Avionics Fixed an issue where wind speeds greater than 99 knots would not be displayed correctly on the X1000 (XPD-17651) Scenery Updated global airports to fix various mesh issues (e.g. VNLK – Tenzing-Hillary / Lukla Airport) Improved docking behavior of Ground Vehicles User Interface & Controls Added a new dataref to indicate if Tobii Eye Tracker is enabled (sim/graphics/view/eq_tobii_eyetracker) Fixed 10 nm approach startup option (XPD-17640) Fixed a crash when using the first monitor as a 2D panel only (XPD-17629) Fixed an issue where mouse clicks where not handled correctly when using 2D panels fullscreen (XPD-17644) Several stability improvements VR Fixed an issue where MSAA 8x caused visual distortion (XPD-17573) Fixed an issue where FXAA caused rendering issues on the right eye screen (XPD-17638) SDK Fixed a crash when closing windows created by plugins (XPD-17624) Fixed an issue where calling XPLMCreateProbe could cause a crash (XPD-17652) Improved internal handling when subscribing to resizable arrays using the WebAPI     Und hier die Übersetzung:   Veröffentlichungsdatum: 10. Januar 2026   Flugzeug Airbus A330-300 Anzeige von QNH auf der PERF APPR-Seite des MCDU korrigiert (XPD-17627) Eingabe von Werten auf der PERF APPR-Seite unabhängig von der aktuellen Flugphase immer zulassen (XPD-17634) Problem behoben, bei dem die Auswahl des Kursmodus ALT CRZ deaktivierte (XPD-17673) Diverse Darstellungsfehler auf dem ND behoben Drehrate des Autopiloten verbessert CLR-Taste am Transponder aktiviert Diverse weitere kleinere Verbesserungen   Flugverkehrskontrolle & Funk Fehlende ATIS-Informationen für einige Flughäfen hinzugefügt (XPD-17630) Avionik Problem behoben, bei dem Windgeschwindigkeiten über 99 Knoten auf dem X1000 nicht korrekt angezeigt wurden (XPD-17651)   Szenerie Globale Flughäfen aktualisiert, um verschiedene Fehler zu beheben Mesh-Probleme (z. B. VNLK – Flughafen Tenzing-Hillary/Lukla) Verbessertes Andockverhalten von Bodenfahrzeugen   Benutzeroberfläche & Steuerung Neue Datenreferenz hinzugefügt, um anzuzeigen, ob der Tobii Eye Tracker aktiviert ist (sim/graphics/view/eq_tobii_eyetracker) Startoption für 10-NM-Anflug korrigiert (XPD-17640) Absturz beim Verwenden des ersten Monitors als reines 2D-Panel behoben (XPD-17629) Problem behoben, bei dem Mausklicks im Vollbildmodus von 2D-Panels nicht korrekt verarbeitet wurden (XPD-17644) Diverse Stabilitätsverbesserungen   VR Problem behoben, bei dem MSAA 8x visuelle Verzerrungen verursachte (XPD-17573) Problem behoben, bei dem FXAA Darstellungsprobleme auf dem rechten Bildschirm verursachte (XPD-17638)   SDK Absturz beim Schließen von Plugin-Fenstern behoben (XPD-17624) Es wurde ein Problem behoben, bei dem der Aufruf von XPLMCreateProbe zu einem Absturz führen konnte. (XPD-17652) Die interne Verarbeitung beim Abonnieren von skalierbaren Arrays über die WebAPI wurde verbessert.

Can anywone please help me out. Goodday i have a question about the honeycomb throttle bravo quadrant i bought in the netherlands at bol.com and another before at coolblue.com.  I checked all the mapping of the switches and sensors in windows 10 hardware properties and i am missing the keystroke of the throttle no 3 . It has 3 contacts and there are only 2 connected and show up in properties.One is ground and other two switched contacts.The no. 1 and no.2 throttles have also 3 contacts but they show up in properties.They are oke! So when i like to connect a third party throttle handle that i obtained from flightsimfactory i can only activate the reverser function and not the TOGA.For a B737 config throttle handle no.3 service as throttle 1 with reverser and A/T disconnect and throttle handle no.4 service as throttle 2 with only reverser. Can not simulate TOGA. It shows at youtube articles that this should work ,thats why I bought the quadrant for.I will use it in FSX.   The spoiler handle is mapped in properties 29 the throttle no. 1 handle is mapped 9 and also on 29 the throttle no.2 handle is mapped 10 and 30 the throttle no.3 handle is mapped only at 11 the throttle no.4 handle is mapped 12 has only 2 contacts  Note 15 and 16 are not mapped! the rest from the 32 functions work. Awaiting for your answer what can be the problem . Seems to be not connected or wire broken. I had the same with an other one bought before at coolblue.com in the netherlands. Please advice, if not i will return it to the shop.I bought the new one yesterdag and i returned already the first one to coolblue.I have made an attempt to contact honeycomb but they repond only with a product and ordernumber purchaced from there shop.I  

Any progress on the update? First and almost second week is past.

Jetzt fehlt nur noch Djerba DTTJ   Frank

Hi Aerosoft,   please check DTTJ (MSFS2024) The installer AS ONE install no Jetways   Thanks   Frank

Mit dem letzten Update, dass jetzt auf Aerosoft One verfügbar ist, sind auch die Jetways wieder vorhanden 😀. Damit ist das Problem bei mir behoben.

I couldn’t solve the problem, so I’m not using Aerosoft Pushback Pro even though I paid for it. I’m using GSX that I borrowed from a friend instead. Thank you for getting back to me so quickly.

MSFS 2024 :  http://freeware.aerosoft.com/forum/downloads/AS_HONEYCOMB_MSFS2024.zip MSFS 2020 :  http://freeware.aerosoft.com/forum/downloads/AS_HONEYCOMB_MSFS.zip

Please post the exact link you are downloading from.

on the Honeycomb Bravo Throttle Quad - I need to know how to get the darn lights working using MSFS Steam version.  I saw a post here that showed it on the 2020 version. Christmas tree lights all activate so that is verified that they work.  Just need the software to recognize it now