"Descent and maintain 0"   Hallo zusammen,   zunächst einmal "Frohes neues Jahr an alle"! Die obige seltsame Anweisung habe ich auf einem IFR-Flug (na ja, so nennt ihn das ATC-Modul nunmal) mit der Baron 58 von EDDF nach EDDK in einer immer wieder kehrenden Schleife bekommen. Ich befand mich zu dieser Zeit ca. 25 NM südlich EDDK in 3.000 ft. Diese Anweisung ist mir völlig rätselhaft, soll ich in Ameisenkniehöhe weiterfliegen??? Da die Anweisung immer weiter in der Schleife blieb bin habe ich sie weggerogert und bin nach eigenem Gusto in EDDK gelandet. Der Spaß war aber weg. Request help!   Herzlichen Dank vorab und happy landings Andreas    

Danke für Deine Nachricht. Ein gutes Neues noch nachträglich. Schöne Grüße

Wenn man die Navigraph Charts installiert hat, dann zeigt Simlink in den Charts die Flugzeugposition an. Simlink verknüpft also X-Plane mit den Charts.   Gruß Horst  

Hallo, ich habe eine Frage zu Navigraph Simlink. Was ist Simlink für ein Programm und wozu wird es verwendet? Welchen Einfluss hat es auf den XP 11 und was kann damit gesteuert werden? Würde mich über Nachrichten freuen.   Grüße

Thanks for all this information.  As promised, I will work on this tomorrow. 

Windows 11 - fully updated  Intel Core i7 14700F NVIDIA GeForce RTX 4070 32GB DDR5 RAM 2TB SSD   Alpha and Bravo - both PC & MAC comp Thrustmaster rudder ctrl Logitech radio panel   I have been trying to get the MSFS 2024 in the XBox-Windows app to interface with my controls.  I have major flight surfaces control of the Cessna 172, but no throttle controls, no LEDs.  In the Alpha, I can only keep the engine running by leaving "key" in the start position.   Since most you fine aviation fans may have similar equipment,  WHY do we all have to go through the frustrating, mind-numbing, blood pressure raising process of mapping and binding our control systems?  WHY can't we share files/folders of our configuration and save the mass Extinction of MSFS 2024 Fandom due to brains exploding onto our simulator desks?   I have tried the two config downloads shown below, running as administrator, but both crashed harder than my first sim flight!   Thank you in advance for your replies.  And FYI, Tylenol Rapid Release Extra Strength is on sale in 300 capsule bottles.

Windows 11 - fully updated  Intel Core i7 14700F NVIDIA GeForce RTX 4070 32GB DDR5 RAM 2TB SSD   Alpha and Bravo - both PC & MAC comp Thrustmaster rudder ctrl Logitech radio panel   I have been trying to get the MSFS 2024 in the XBox-Windows app to interface with my controls.  I have major flight surfaces control of the Cessna 172, but no throttle controls, no LEDs.  In the Alpha, I can only keep the engine running by leaving "key" in the start position.   Since most you fine aviation fans may have similar equipment,  WHY do we all have to go through the frustrating, mind-numbing, blood pressure raising process of mapping and binding our control systems?  WHY can't we share files/folders of our configuration and save the mass Extinction of MSFS 2024 Fandom due to brains exploding in our simulator desks?   I have tried the two config downloads shown below, running as administrator, but both crashed harder than my first sim flight!   Thank you in advance for your replies.  And FYI, Tylenol Rapid Release Extra Strength is on sale in 300 capsule bottles.

I performed a lot of "dances" with Vjoy and Omsi.  Reviewed all kinds of variations but no positive results.  What is striking is that the changes on the axes are implemented neatly, but Omsi refuses to see more than 1 button, Omsi continues to see that one button, even if the number of buttons on the VJoy is zero.  Apparently Omsi does not see any buttons on the VJoy and places 1 button on it by default. Funny enough, that one button does work. I use that in my workaround mentioned above.   I also tried it on a clean Omsi installation. Same result here too, only one button.   What did i test: - Add and remove devices; - Reinstall the Vjoy app; - Removed all drives; - Set VJoy on and off in the device manager; - Removed all related Omsi files (gamecontroler config and settings) - Did a fresh reinstall of Omsi. - Made several VJoy devices, with more then one VJoy device Omsi will list them all (same name) but the settings for all dfferent devices are the same while i did set them up with different axes and amount of buttons.   I give it up for now.  

copy/paste this from the FAQ. If you go to AerosoftOne > library > A330.... Get Support   The procedure below worked for me.     Blank screens usually indicate that Aerosoft One Utilities is not running on your system. To resolve this issue, follow the steps in one of the sections below. [Recommended] Reinstall Aerosoft One Utilities and the Aircraft Restart your PC and then launch Aerosoft One. Go to Library > Dependencies > Installed and uninstall the Aerosoft One MSFS Utilities. Go to Library > Microsoft Flight Simulator > Installed Add-ons and uninstall the A330. Go to Library > Microsoft Flight Simulator > Available Add-ons and re-install the A330 (this will also automatically re-install the Aerosoft One MSFS Utilities). The aerosoft-aircraft-a333-pw shortcut/folder and aerosoft-one-msfs-utilities folder should now exist in your <MSFS Packages>\Community folder. Launch MSFS and check if the A330 is now working.   Manually start Aerosoft One Utilities Restart your PC and then open the folder <MSFS Packages>\Community\aerosoft-one-msfs-utilities\utilities. Double-click on Aerosoft One MSFS Utilities.exe (the application will start without creating any visible windows). Launch MSFS and check if the A330 is working now.   Manually start Aerosoft One Utilities as an Administrator Restart your PC and then open the folder <MSFS Packages>\Community\aerosoft-one-msfs-utilities\utilities. Right-click on Aerosoft One MSFS Utilities.exe and then click Run as administrator (the application will start without creating any visible windows). Launch MSFS and check if the A330 is working now. If the issue is not resolved after performing the above steps, contact our support team here, and provide us with your Aerosoft One log files, so our team can investigate the issue further. The log files can be found in the following locations: C:\Users\<username>\AppData\Roaming\Aerosoft One\logs\aerosoft-one.log C:\Users\<username>\AppData\Roaming\Aerosoft One\logs\aerosoft-one.old.log <MSFS Packages>\Community\aerosoft-one-msfs-utilities\logs\aerosoft-one-msfs-utilities-exe.log Note that not all log files may be present.

So check what has changed on your system Also make sure to run FSX with administrative rights.