I'm a sad marketplace user, so am happy that this was finally released today.  Did a quick test hop from KDEN to KCYS a la SKW5083.  Everything was also going well until I crossed AIMES en route to HAMER.  I noticed the ND froze, the EFB froze, then basically everything froze, except I could still mouse over switches and toggle them, but it didn't do anything.  The yoke was still animated, but throttles appeared frozen.  I could still hear the engines changing pitch with the physical throttles though.  Managed to land. . .sort of.  I'm sure pax barfed.   I'll check again tomorrow, but that was quite disappointing.  I did use the -700ER with the "SilkySmooth" livery pack for V2 off of FS.to.  I'll try an "official" livery tomorrow.

Not sure what step I missed but on my last flight from KMSP to KRAP, I did not have a TOD or descent data shown on the MFD (see attached picture) I selected ILS 32 and a IAF with no disco's. I even added a hard altitude to the IAF (/5500).   Another oddity is I am about 30 miles from KRAP (range ring) but the data block on the MFD for KRAP shows 251nm to go.   Does anyone know what I did wrong?   Thanks

I was having a hard time adjusting the landing elevation knob for the pressurization and looking at the display in VR (the mouse pointer would move off the knob and move to my viewpoint after a second or two).  The Lvar for this adjustment is "ASCRJ_PRESS_LDG_ELEV_DELTA" The adjustment is just a 1 or an -1. I have it on repeat and it works great. Hopefully this is helpful to anyone who is having trouble with this adjustment.  

Just checking in on this bug, as  I'm experiencing the same behavior. The N1s should drive to the FLEX value rather than the normal takeoff TOGA.

Infuriating.  After taking a month to show up on Xbox, it finally did today.  It works on 2020, but on 2024 it is stuck on the “disabled not available” status. Cant enable it yet.   So after all this wait, and marketing and function for both sims and all platforms, we still can’t use it.     Ccmon aerosoft and Microsoft. What’s the deal, please look into this.  $50 is half wasted if can’t use it in 2024 as advertised.     @Tom @Marius Ellenbürger

...ist der Titel einer Doku über die deutschen Standorte von Airbus.   Zwar ist das Video schon 5 Jahre alt. Da wurde der A380 noch gebaut. Trotzdem fand ich das Material hoch interessant. Die Logistik, die Innovation und viele technische Details haben mich begeistert 🙂 (Das hat mich gleich inspiriert, mal mit X-Plane nach Finkenwerder zu fliegen).Was ich noch nicht wusst: Die A320 Familie wird hier endmontiert und ausgeliefert. Viel Spaß bei der spannenden Doku.    

Hallo Herrmann, ich kann mich allen Vorredner anschließen. Das war wieder ein beeindruckendes Video und so schlecht war die Landung gar nicht.

Hallo Hermann,wieder im Lande, habe ich Dein Video grade entdeckt und angesehen. Wie immer bin ich begeistert über Dein wissen und wie du es mit uns Unwissenden teilst! Ich habe wieder sehr viel gelernt, vor Allem die Checkphase ist äußerst informatiert. Der Flug war auch wunderschön, ich finde auch gerade das Wetter, ein wolkenloser Himmel ist doch fad! Habe es sehr genossen.   Viele Grüße, Stefan    

Made a post in the other thread about this too -- I've had this happen three times in the default Delta / Endeavor CRJ-900 livery (out of four attempted flights). Never had the freeze occur in any other livery or model though, which is very odd. Plane works great with anything else.

Made an account to also bump this. From what I can tell, this is a livery-specific issue (somehow, not sure why). Did 4 flights in the stock Delta (Endeavor) CRJ-900 livery, 3/4 of the flights froze up. Once on the ground, twice in the air, somewhere between 30-90 minutes after sim started. Did 5 flights in other variations and liveries and had zero issues, plane worked great. The only other plugin I have in MSFS 2024 is GSX Pro, and my windows is a clean install, so I highly doubt this is a sim issue -- definitely a plane issue.   As the OP stated, the displays, EFB, FMS, and buttons (with limited exceptions such as AP disconnect and gear handle) completely freeze and do not work. It's as if the plane's code just crashed. MFD and PFD will freeze at the state they were in at the time. The aircraft physics and external simulation continue to work, so I can disconnect AP and fly around still. Waited 30 minutes after the freeze yesterday and it didn't resolve itself.   Hope this helps, devs!