Scott Gist 4 Posted March 17, 2021 Share Posted March 17, 2021 Well I’ve been at it all day trying to figure this out with no luck. The problem is engine 1 does not seem to work in many ways. First I tried to use the EFB to just set ready to taxi state, but engine 1 just sits at N1 of 3 and N2 of 25. Engine 2 starts normally. If I hit CNTL E it appears to start and N1/N2 match engine 2. At this point it appears to be running, but now I have little control. After calibration (Honeycomb Bravo) via MSFS and the EMB as explained in the tutorial when I advance the throttles to max engine 2 goes to 92.9 N1 and 93.7 N2, engine 1 only goes to 28-29 N1 and 65-66 N2 and fluctuates +/- 2. The problem is also present in reverse thrust, engine 2 gets 60 N1 and 80 N2 in reverse, engine 1 only 26 N1 and 63 N2 with a +/- fluctuation of 1-2%. I have read through all the forums her and tried many thing, but no luck. Any help would be appreciated. Thx Link to comment Share on other sites More sharing options...
Scott Gist 4 Posted March 17, 2021 Author Share Posted March 17, 2021 Video of the problem. Please login to view this video. Link to comment Share on other sites More sharing options...
ual763 81 Posted March 17, 2021 Share Posted March 17, 2021 When you calibrated the throttles in the EFB, did you select the multi-axis option? Link to comment Share on other sites More sharing options...
Scott Gist 4 Posted March 17, 2021 Author Share Posted March 17, 2021 Yes 1 Link to comment Share on other sites More sharing options...
ual763 81 Posted March 17, 2021 Share Posted March 17, 2021 Well in that case, I’m not sure. Hans will be on here in the morning I’m sure to help you. Perhaps try just setting just one axis for now. Link to comment Share on other sites More sharing options...
Scott Gist 4 Posted March 17, 2021 Author Share Posted March 17, 2021 Tried the single axis and in MSFS using one throttle for all engines and still persist. The bad engine #1 also keep shutting down by itself. Link to comment Share on other sites More sharing options...
Developer Hans Hartmann 3695 Posted March 17, 2021 Developer Share Posted March 17, 2021 If it is shutting down itself, there is probably some control binding that cuts off the fuel for it. You should check Options|Controls for this. Link to comment Share on other sites More sharing options...
Scott Gist 4 Posted March 17, 2021 Author Share Posted March 17, 2021 Well, two days of nonstop troubleshooting with no luck, tried clear community folder, new control profiles with nothing in them but throttle control and this problem persists. I try to set the plane for “ready to taxi” on the EFB and engine 1 won’t get above 26% N2 and still fluctuates when throttles are move to Max or TO. Frustrated, this is just not flyable like this. Link to comment Share on other sites More sharing options...
PWS Plane 10 Posted March 18, 2021 Share Posted March 18, 2021 I have exactly the same problem as he never, the number one engine does not start us me it goes down in percentage all the time, I sat for 4 hours yesterday trying without it helping Link to comment Share on other sites More sharing options...
PWS Plane 10 Posted March 18, 2021 Share Posted March 18, 2021 Please login to display this image. Link to comment Share on other sites More sharing options...
GEK_the_Reaper 233 Posted March 18, 2021 Share Posted March 18, 2021 In the Controls settings in MSFS you can search key bindings by inputs. Please take your time and search if your bindings are correct especially the axis. It is probably as Hans mentioned a binding that interferes. 1 Link to comment Share on other sites More sharing options...
Scott Gist 4 Posted March 18, 2021 Author Share Posted March 18, 2021 I created new profiles for all input devices where there is nothing assigned except the throttle axis in my Bravo throttle and the problem persist. 1 Link to comment Share on other sites More sharing options...
GEK_the_Reaper 233 Posted March 18, 2021 Share Posted March 18, 2021 vor 2 Stunden , Scott Gist sagte: I created new profiles for all input devices where there is nothing assigned except the throttle axis in my Bravo throttle and the problem persist. I was just online with @PetterWS and we created new empty profiles for all hes controllers (so basically we emptied everything). The ENG started normal and did not shut off. He also has the Bravo and we cleared that also. 1 Link to comment Share on other sites More sharing options...
PWS Plane 10 Posted March 18, 2021 Share Posted March 18, 2021 @GEK_the_Reaper thank you for your patience! good man! Link to comment Share on other sites More sharing options...
ual763 81 Posted March 18, 2021 Share Posted March 18, 2021 3 hours ago, Scott Gist said: I created new profiles for all input devices where there is nothing assigned except the throttle axis in my Bravo throttle and the problem persist. Check the bindings for fuel shutoff as well 1 Link to comment Share on other sites More sharing options...
gblackwood 0 Posted March 19, 2021 Share Posted March 19, 2021 Hi I have the same problem, it seams to be in the fuel flow on the #1 engine, if when starting #2 watch the FF when it reaches 450 the engine spools up but #1 never passes 50. need to find out why the FF is not increasing Link to comment Share on other sites More sharing options...
Deputy Sheriffs Secondator 643 Posted March 20, 2021 Deputy Sheriffs Share Posted March 20, 2021 Hi gblackwood, Did you check all the control bindings to make sure that nothing is interfering with fuel or engine starter?c Link to comment Share on other sites More sharing options...
Thx1137 65 Posted March 21, 2021 Share Posted March 21, 2021 On 3/18/2021 at 6:40 PM, GEK_the_Reaper said: In the Controls settings in MSFS you can search key bindings by inputs. Please take your time and search if your bindings are correct especially the axis. It is probably as Hans mentioned a binding that interferes. But don't just look for "throttle". Look for any "always on" type switch that can prevent the engine from starting. Like fuel cutoff, fuel pump, etc. Link to comment Share on other sites More sharing options...
Meijer 2 Posted August 12, 2022 Share Posted August 12, 2022 Had the same engine indications. I cold and dark state the N1 and 2 rose immediately to N1 3 and N2 to 25. I puzzled for hours. After hours I noticed the engine start switch on the Alfa yoke was in the start position. Turnes that switch to off and the N1 and N2 indications turned to 0. Never thought of that before. 2 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now