bhorv67 12 Posted August 6, 2017 Share Posted August 6, 2017 Is anyone else having issues when you're on intercept course to capture the ILS and glideslope, yet when you approach the center line, the ILS needle doesn't move until you're past that point? I thought this was a problem just at one airport, but every flight I'm doing, I'm noticing this behavior, unless the CRJ really does that in real life. Link to comment Share on other sites More sharing options...
blahhh 41 Posted August 6, 2017 Share Posted August 6, 2017 did u switch the source to vor/loc? Link to comment Share on other sites More sharing options...
bhorv67 12 Posted August 6, 2017 Author Share Posted August 6, 2017 I think that's the issue - I can't move the yoke out of the way to get to the source knob during flight. I've tried loading the Piper cub before the CRJ. That worked once. Link to comment Share on other sites More sharing options...
doylie22 23 Posted August 6, 2017 Share Posted August 6, 2017 30 minutes ago, bhorv67 said: I think that's the issue - I can't move the yoke out of the way to get to the source knob during flight. Click the black vRef placard above the MFD and it will hide the yoke. Link to comment Share on other sites More sharing options...
bhorv67 12 Posted August 6, 2017 Author Share Posted August 6, 2017 That's the problem I'm having. The clickspot doesn't work. I've taken the recommendation from others to spawn with a different aircraft, such as the Piper Cub, then load the CRJ. That worked for me one time. Last night I tried a night flight for the first time, loaded the Cub, then the CRJ, then tried to hide the yoke, it flashes for second but doesn't hide. Link to comment Share on other sites More sharing options...
FraPre 89 Posted August 6, 2017 Share Posted August 6, 2017 The problem is, Sometimes it works, sometimes not. I click immediately after the simulation start, then it works. I forget that and change the views, or open sub panels, i can have bad luck and do not get it away. Link to comment Share on other sites More sharing options...
blahhh 41 Posted August 6, 2017 Share Posted August 6, 2017 55 minutes ago, FraPre said: The problem is, Sometimes it works, sometimes not. I click immediately after the simulation start, then it works. I forget that and change the views, or open sub panels, i can have bad luck and do not get it away. thanks for the tip I'll try it Link to comment Share on other sites More sharing options...
Paalsson 2 Posted August 6, 2017 Share Posted August 6, 2017 Have you tried shift + Q to hide the yoke? Dont know if that would be different to the clickspot Link to comment Share on other sites More sharing options...
bhorv67 12 Posted August 7, 2017 Author Share Posted August 7, 2017 Is there a way to assign a key command to the Source selector knob until the yoke hide issue is sorted? Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted August 7, 2017 Aerosoft Share Posted August 7, 2017 On 8/6/2017 at 2:30 AM, bhorv67 said: Is anyone else having issues when you're on intercept course to capture the ILS and glideslope, yet when you approach the center line, the ILS needle doesn't move until you're past that point? I thought this was a problem just at one airport, but every flight I'm doing, I'm noticing this behavior, unless the CRJ really does that in real life. Please note that there is an ILS intercept issue in V4 that has been reported to Lockheed. Link to comment Share on other sites More sharing options...
simon747 98 Posted August 7, 2017 Share Posted August 7, 2017 1 hour ago, Mathijs Kok said: Please note that there is an ILS intercept issue in V4 that has been reported to Lockheed. Gonna start my landing practice Tuesday; is p3d v3 ok for ils capture etc? Cheers, simon Link to comment Share on other sites More sharing options...
Airbus666 13 Posted August 7, 2017 Share Posted August 7, 2017 P3D V3 has no issues concerning ILS interceptions. Link to comment Share on other sites More sharing options...
Mogens Gaardbo 0 Posted August 7, 2017 Share Posted August 7, 2017 22 hours ago, FraPre said: The problem is, Sometimes it works, sometimes not. I click immediately after the simulation start, then it works. I forget that and change the views, or open sub panels, i can have bad luck and do not get it away. If you load the simulator with a plane in 2D cockpit-view, the the clickspot only get the yoke to flash, but still will be there. My experience is, at you have to be in 3D cockpit view of the default airplane, and then change to the CRJ. Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted August 7, 2017 Aerosoft Share Posted August 7, 2017 4 hours ago, Airbus666 said: P3D V3 has no issues concerning ILS interceptions. Indeed, what we see is introduced with the new V4. We often forget that we are using a very new simplatform that still needs to to stabilize. Link to comment Share on other sites More sharing options...
simon747 98 Posted August 7, 2017 Share Posted August 7, 2017 7 hours ago, Airbus666 said: P3D V3 has no issues concerning ILS interceptions. 2 hours ago, Mathijs Kok said: Indeed, what we see is introduced with the new V4. We often forget that we are using a very new simplatform that still needs to to stabilize. on v3 so can start my practice landings with self confidence Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted August 7, 2017 Aerosoft Share Posted August 7, 2017 Yes. We all tend to forget how new P3d V4 is. Link to comment Share on other sites More sharing options...
simon747 98 Posted August 7, 2017 Share Posted August 7, 2017 Stick with v3 for a bit longer; works great for me Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.