HB-JHM 20 Posted August 16, 2021 Share Posted August 16, 2021 Good morning Guys Yesterday, I landed at EDDB airport and after vacating the RWY 25L, the airplane stucked on the taxiway. Then I found out that at some postion by the C stands, I have the same issue. I have installed the latest version. Does anybody have an idea, how to solve this issue? brgds Massimo Link to comment Share on other sites More sharing options...
HB-JHM 20 Posted August 18, 2021 Author Share Posted August 18, 2021 any help? thanks Massimo Link to comment Share on other sites More sharing options...
HansW 28 Posted August 20, 2021 Share Posted August 20, 2021 What do you mean with "stuck"? That you need much power to move the aircraft? When yes then the underground is "weak". You can test that by looking from outside and moving the aircraft more than about 8-10 kts. Then gravel is showing up around the wheels flying around. I tested the south runway (25L-07R) with the default Commander and found all the taxiways are "hard" covered here in my P3Dv4.5HF3. Do you have Berlin Brandeburg Intl. activated in the configurator? Do you have Orbx GEN installed? Hans Link to comment Share on other sites More sharing options...
HB-JHM 20 Posted August 25, 2021 Author Share Posted August 25, 2021 On 20.8.2021 at 14:33, HansW sagte: That you need much power to move the aircraft? When yes then the underground is "weak". Do you have Berlin Brandeburg Intl. activated in the configurator? Do you have Orbx GEN installed? Hans Hi Hans Correct I have to use much power max toga to move the aircraft. I have installed the configurator No germany north Gen installed. cheers Massimo Link to comment Share on other sites More sharing options...
Deputy Sheriffs mopperle 4162 Posted August 25, 2021 Deputy Sheriffs Share Posted August 25, 2021 When you run the ASUpdater, which productversion is shown for EDDB? In OC is the Library Insertion Point set below the lowest 3rd party add-non? Link to comment Share on other sites More sharing options...
HB-JHM 20 Posted September 7, 2021 Author Share Posted September 7, 2021 On 25.8.2021 at 14:05, mopperle sagte: When you run the ASUpdater, which productversion is shown for EDDB? It's version 1.0.3.0 what do you mean with this question: In OC is the Library Insertion Point set below the lowest 3rd party add-non? @mopperle Link to comment Share on other sites More sharing options...
Deputy Sheriffs mopperle 4162 Posted September 7, 2021 Deputy Sheriffs Share Posted September 7, 2021 Open OrbxCentrl (OC) go to settings and make sure that the Library Insertion Point is set below the lowest 3rd party add-non Link to comment Share on other sites More sharing options...
HB-JHM 20 Posted September 11, 2021 Author Share Posted September 11, 2021 just to be on the safe side, the airport EDDB should below correct in the library? Link to comment Share on other sites More sharing options...
Deputy Sheriffs mopperle 4162 Posted September 11, 2021 Deputy Sheriffs Share Posted September 11, 2021 5 hours ago, HB-JHM said: ust to be on the safe side, the airport EDDB should below correct in the library? NO! The Library insertion Point has to be below the lowest 3rd Party Add-on, not EDDB. This has been in detailed explained many times. Please check your Orbx documentation and/or their Website/Forum. Link to comment Share on other sites More sharing options...
dhazelgrove 42 Posted September 12, 2021 Share Posted September 12, 2021 OK. Let's take this slowly. In your sim (I'm assuming P3Dv5, but this also applies to any of the others bar M$FS) go to the scenery library. In the list, look for the lowest entry that YOU put there -- either via direct entry or addon installer. Make a note of this item. Exit the sim. Go into ORBX Central and click on the Settings cogwheel (top line on the right). In the Settings window that opens, at the bottom on the left you'll see "Insertion Point". Click on this. Under 'ORBX Airports and Regions' there's a drop-down list. Click on this and select the item you noted earlier. There's another drop-down list under 'ORBX Global openLC'. Leave this one strictly alone. That's it. You're done. Easy, wasn't it? Dave Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.