Jump to content
generale84

Checklist Stuck

Recommended Posts

Hi

 

checklist on 330 maybe stick on OFF command about Seat Bealt after takeoff.

Impossible to reset or turn it off (DELAY OFF also stuck)

Share this post


Link to post
Share on other sites

Same issue i just had, also the co pilot isn't turning on the strobes or wing lights during take off phase for me. 

Share this post


Link to post
Share on other sites

The light settings are normally SOP content e. g. differ from airline to airline. In the CL we can only use one.

  • Seat Belts: OFF after passing 20.000 feet and ON again when initiating descend
  • NoPED: AUTO e.g. signs in the cabin are automatically going OFF when flaps are set to "0" and ON when set to "1"
  • STROBES: AUTO
  • WING: Are only set to ON in case of an emergency evacuation

Regards,

Rolf

 

 

Share this post


Link to post
Share on other sites

I too have just had the endlessly repeating "off - off - off" for the seatbelt signs. I had to close p3d for relief.A problem with the checklist I'm afraid.

Chris

Share this post


Link to post
Share on other sites

When did this start and were you using the cl and the copilot?

Share this post


Link to post
Share on other sites

I set Seat Belt OFF after 8.000 ft; automatic check list at FL200 try to do what you explain, but find switch off and going stuck I suppose

Share this post


Link to post
Share on other sites

I am currently in flight and have the same problem with the checklist getting stuck and I now have endless „off, off, off, off ....“ sound.

 

The auto checklist at FL100 did not trigger so I manually switched off LDG and seatbelt lights between FL100 - FL110.

 

It seems the FL100 checklist triggered far too late (a few thousand feet later, can‘t remember when exactly) and loops on the lights check because I switched them manually. Skipping item is not possible.

Share this post


Link to post
Share on other sites

Which exact version of P3Dv4 are you using. Please post the version number of the prepar3d.exe.

And on which version of the A330 are you? Run the ASUPdater to check.

Share this post


Link to post
Share on other sites

P3D4 Version 4.5.13.32097

 

A330 Version 1.0.0.2

 

The A330 was up to date prior to my flight, just noticed that 1.0.0.4 is now available ...

Share this post


Link to post
Share on other sites
vor 20 Stunden , Hanse sagte:
  • Seat Belts: OFF after passing 20.000 feet and ON again when initiating descend
  • NoPED: AUTO e.g. signs in the cabin are automatically going OFF when flaps are set to "0" and ON when set to "1"

At 10.000 feet only the Landing Lights are switched off. Regarding Seat Belt and NoPED signs please read my statement above....... There were also some problems with lights during TAXI but those are solved. Please update to 1.0.0.4.......!

Share this post


Link to post
Share on other sites

Just had the "Light OFF" and "Seatbelt Sign OFF" stuck in checklist.

Version 1.0.0.6.

 

I guess this is due to high altitude departure from SLLP. On other airport I haven't seen this issue for weeks now.

Share this post


Link to post
Share on other sites

Thomas, please explain your problem a little bit more in detail so that I am able to try to reproduce the issue. What do you mean by "stuck" for LIGHTS OFF as well as for "SEAT BELTS".  Are you talking after departing from SLLP at 10.000 resp. 20.000 feet? Normally those functions are based on the actual altitude of the plane regardless the altitude of the departing airport.

I just realized that SLLP is already at app. 13.000 feet e. g. the "LIGHTS OFF" are already triggered before TO. This is a special situation for which I currently have no solution........

 

 

Rolf

Share this post


Link to post
Share on other sites

A new update 1.0.0.7 is available now which regarding the checklist and copilot solves the following issues:

  • BEFORE ENGINE START CL: Starting issue in connection with GSX closing doors - solved -
  • ECAM PAGES: Manually selected by CL are now reset to standard when next CL item is called
  • CHRONO FO: Set ON when takeoff thrust is set and stopped after landing
  • VC LIGHTS: When C&D as well as TO state is used VC-lights are automatically set to "flight" when TAXI CL is started
  • LANDING LIGHTS: Were not really ON after descending below 10k feet even that OVHD switch was ON - solved  
  • BEFORE TAKEOFF - Landing Lights are now automatically switched on when plane enters the departure runway.

I therefore will close this topic and ask you if there are still " checklist issues" to open a new thread.

 

Regards,

Rolf

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.

×
×
  • Create New...