Recently we have seen a lot of codes used to unlock our products being offered for discounted prices. Almost all of them are bought using stolen credit cards. These codes will all be blocked by our systems and you will have to try to get your money back from the seller, we are unable to assist in these matters. Do be very careful when you see a deal that is almost too good to be true, it probably is too good to be true.

Jump to content
flyingpilot1740

Seat belt sign switch after landing

Recommended Posts

Hello all,

 

I have no idea if that works as designed but I am not able to set the seat belt sign to OFF after arriving at the gate.

After 2-3 minutes, I am able to turn it off :-S

 

Can anybody explain this to me, or does anybody have the same behaviour? :)

 

Thanks

Bernd

Share this post


Link to post

Same issue here. Can't click it off - it starts to toggle down but pops right back up to "ON" again. This results in checklist calling for "cabin signs?" many times.

This only happened on one flight so far. I am on latest beta version available as of September 3rd, 2018.

Share this post


Link to post
vor 3 Stunden , MDFMike sagte:

Same issue here. Can't click it off - it starts to toggle down but pops right back up to "ON" again. This results in checklist calling for "cabin signs?" many times.

This only happened on one flight so far. I am on latest beta version available as of September 3rd, 2018.

 

Question to you cause I think this happend only if FS2Crew is used.

Are you using FS2Crew?

Share this post


Link to post
vor 2 Stunden , MDFMike sagte:

Not using FS2Crew.

 

Okay. I found out more. If you continuously click on the knob, after 8 clicks, it turns to off Funny

 

I had this strange behaviour in the A319-321

Share this post


Link to post
19 minutes ago, Mert Aydın said:

Same problem. Seat Belts and PED can't be turn ON final approach

 

That's not the same issue hey?

Share this post


Link to post
53 minutes ago, Mathijs Kok said:

 

That's not the same issue hey?

I did not want to open a new topic sir. 

Share this post


Link to post

Are you using the checklist and copilot function? I assume not? But one thing is for sure: The cabin signs should be switched on after passing 10000 feet and to Off after setting the parking brake and the engines are cut.  If this does not work on your system, then there is a bug......

 

Regards,

Rolf

Share this post


Link to post
vor 1 hour , Hanse sagte:

Are you using the checklist and copilot function? I assume not? But one thing is for sure: The cabin signs should be switched on after passing 10000 feet and to Off after setting the parking brake and the engines are cut.  If this does not work on your system, then there is a bug......

 

Regards,

Rolf

 

Hey,

 

I am not using Copilot and Checklist function :)

As described, I am able to turn them off by continuously clicking the button. After 8 clicks, they went to OFF :)

 

No Problem at the beginning of the flight. I can turn them off and on without issues.

DEF State is Cold and Dark :)

Share this post


Link to post

No, the issue discussed what now being able to switch it off and you discussed switching it on. If there is an issue switching it on (so far only reported by you as far as I know) that is a different issue. I just tried it and did not see an issue.

Share this post


Link to post
21 hours ago, Mathijs Kok said:

No, the issue discussed what now being able to switch it off and you discussed switching it on. If there is an issue switching it on (so far only reported by you as far as I know) that is a different issue. I just tried it and did not see an issue.

Well after I land and park at the gate, and excuse me for coming into this conversation here, but at the gate I shut off the engines and go to turn off the seatbelt switch it doesn’t work. It’s not turning off. FS 2 crew asks me is the seatbelt sign off and are you sure about that. 

Share this post


Link to post

Hi there,

I noticed this issue today with the A319-CFM Professional in P3D4.4; at the end of a flight with checklists & co-pilot both on; and without fs2crew installed.

 

After engine shutdown; with APU & APU Bleed on; chocks in; Seat Belt switch would not stay in the OFF when clicked.

Same happens after ground power connected and APU switched off.

Most unusual is that the Passenger disembarkation noises play, despite the Seat Belts sign being "ON'.

 

Hope that info helps,

Chris.

Share this post


Link to post

Happening to me too.

After arriving at the gate and switching off engines and parking brake on I can't switch sign off. I'm using fs2crew too.

Share this post


Link to post

same here , i use the inbuilt FO not FS2CREW

Share this post


Link to post

And you have our checklist completely deactivated? 
I don't see how we can prevent FScrew from locking that parameter.

Share this post


Link to post
3 hours ago, Mathijs Kok said:

And you have our checklist completely deactivated? 
I don't see how we can prevent FScrew from locking that parameter.

not sure if you were ref to my post but i dont use FS2CREW just in inbuilt checklist/FO

Share this post


Link to post

Whatever happened mine it seemed to fix itself after the last update. Oh well I guess it’s fixed lol

Share this post


Link to post

 

Funny you should say that mine has too even after i rolled back to 1.2.2,1

Share this post


Link to post
4 hours ago, keenrw said:

 

Funny you should say that mine has too even after i rolled back to 1.2.2,1

Weird stuff 

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...