oyvindd 1 Posted December 6, 2014 Share Posted December 6, 2014 Im unable to go past M0.95 level flight @ 20000 feet with max burner M0.91 in MIL Is this real? Link to comment Share on other sites More sharing options...
jcagle 180 Posted December 6, 2014 Share Posted December 6, 2014 That sounds odd, might be silly, but is anything extended (like speed brakes)? Also, what version of FSX are you running? Link to comment Share on other sites More sharing options...
oyvindd 1 Posted December 6, 2014 Author Share Posted December 6, 2014 That sounds odd, might be silly, but is anything extended (like speed brakes)? Also, what version of FSX are you running? Speed breaks are in. FSX Acceleration Its the same in clean and loaded config Link to comment Share on other sites More sharing options...
jcagle 180 Posted December 6, 2014 Share Posted December 6, 2014 Can you sen a screenshot with the 2D panel at [sHIFT+1] activated? Link to comment Share on other sites More sharing options...
oyvindd 1 Posted December 6, 2014 Author Share Posted December 6, 2014 Can you sen a screenshot with the 2D panel at [sHIFT+1] activated? Link to comment Share on other sites More sharing options...
oyvindd 1 Posted December 6, 2014 Author Share Posted December 6, 2014 Level flight.jpg Trottles are all the way FWD FF just below 7 and marginal change in FF from MIL Nozzle pos around 3 Link to comment Share on other sites More sharing options...
evvatc 12 Posted December 6, 2014 Share Posted December 6, 2014 I'm assuming you are using either a separate throttle or a slider on your joystick. If you are, please double check and make sure it is properly calibrated. If you are in zone 5 burner in the A model or max burner in the B, you would notice a higher fuel flow rate and the nozzle position would be at 5. Link to comment Share on other sites More sharing options...
oyvindd 1 Posted December 6, 2014 Author Share Posted December 6, 2014 I'm assuming you are using either a separate throttle or a slider on your joystick. If you are, please double check and make sure it is properly calibrated. If you are in zone 5 burner in the A model or max burner in the B, you would notice a higher fuel flow rate and the nozzle position would be at 5. Yes i have and old MS sidewinder joy stick. I tested it with my VRS superbug, works OK Uninstalled and reinstalled F-14 Now i have more burner with a 2 below temp. FF max but nozzles below 3 By the way after reinstalling i got tacpac error Link to comment Share on other sites More sharing options...
evvatc 12 Posted December 6, 2014 Share Posted December 6, 2014 Here is some screenshots of what the engine instruments would typically read in Zone 5 or Max burner Link to comment Share on other sites More sharing options...
Halbi 21 Posted December 7, 2014 Share Posted December 7, 2014 Same problem. Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted December 7, 2014 Aerosoft Share Posted December 7, 2014 First of all I suggest calibrating the throttles. Link to comment Share on other sites More sharing options...
Halbi 21 Posted December 7, 2014 Share Posted December 7, 2014 everything is calibrated. i also tried different options in fsuipc but nothing helped. Link to comment Share on other sites More sharing options...
oyvindd 1 Posted December 7, 2014 Author Share Posted December 7, 2014 everything is calibrated. i also tried different options in fsuipc but nothing helped. Trottle calibrated, cant get more than stage 2 of burner if the 2 in mini HUD below temp is burner stage. If i use shift+F4 it just flickes to 4 and goes back to 2 Link to comment Share on other sites More sharing options...
peter197 32 Posted December 7, 2014 Share Posted December 7, 2014 If the FF isn't above 7, then afterburner isn't engaged. Link to comment Share on other sites More sharing options...
peter197 32 Posted December 7, 2014 Share Posted December 7, 2014 actually,disable your throttle, or disconnect, and then try it. The other issue may be that the throttle null zones and sensitivity are incorrect. That can prevent full motion. So remove null zones and full sensitivity. Link to comment Share on other sites More sharing options...
Halbi 21 Posted December 7, 2014 Share Posted December 7, 2014 i cant get a fuel flow over 11. null zones are cleared, sensitivity is checked. did i set sth up wrong in fsuipc? fuel flow 11 on the ground and 7 in the air Link to comment Share on other sites More sharing options...
Erikki 3 Posted December 7, 2014 Share Posted December 7, 2014 Hi Halbi, To make it easy, i to think you should disconnect your throttle. Then use the F4 key to get to full afterburner, and see if you can get past M 1.0 If that is working then we know for sure it has something to do with your throttle settings and we can have a furter look. Link to comment Share on other sites More sharing options...
oyvindd 1 Posted December 7, 2014 Author Share Posted December 7, 2014 Hi Halbi, To make it easy, i to think you should disconnect your throttle. Then use the F4 key to get to full afterburner, and see if you can get past M 1.0 If that is working then we know for sure it has something to do with your throttle settings and we can have a furter look. Disconnected joystick and got stage 4 burner, only stage 2 with joystick connected Link to comment Share on other sites More sharing options...
Halbi 21 Posted December 7, 2014 Share Posted December 7, 2014 even with f4 it doesnt work for me. where can i see in which stage of afterburner i am in? Link to comment Share on other sites More sharing options...
oyvindd 1 Posted December 7, 2014 Author Share Posted December 7, 2014 Hi Halbi, To make it easy, i to think you should disconnect your throttle. Then use the F4 key to get to full afterburner, and see if you can get past M 1.0 If that is working then we know for sure it has something to do with your throttle settings and we can have a furter look. Fixed it by adding throttle axis in fsuipc Link to comment Share on other sites More sharing options...
Erikki 3 Posted December 7, 2014 Share Posted December 7, 2014 Nice! Enjoy! Link to comment Share on other sites More sharing options...
Halbi 21 Posted December 7, 2014 Share Posted December 7, 2014 I already assigned an axis for the trottle in Fsuipc but it doesn't work Link to comment Share on other sites More sharing options...
Halbi 21 Posted December 7, 2014 Share Posted December 7, 2014 So, does anyone have a fix for this? Link to comment Share on other sites More sharing options...
jcagle 180 Posted December 7, 2014 Share Posted December 7, 2014 Have you gone into the Joystick Calibration menu and set the upper and lower limits of the throttle movement? Link to comment Share on other sites More sharing options...
Halbi 21 Posted December 7, 2014 Share Posted December 7, 2014 Yes. Everything is calibrated Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.