jer029 7 Posted August 20, 2017 Share Posted August 20, 2017 When checking fsuipc logging I've noted that the following items continually log for CRJ700: 480483 *** AXIS: Cntrl= 65786 (0x000100fa), Param= 5406 (0x0000151e) SPOILERS_SET 480545 *** AXIS: Cntrl= 65786 (0x000100fa), Param= 5406 (0x0000151e) SPOILERS_SET 480592 *** AXIS: Cntrl= 65786 (0x000100fa), Param= 5406 (0x0000151e) SPOILERS_SET 480670 *** AXIS: Cntrl= 65786 (0x000100fa), Param= 5406 (0x0000151e) SPOILERS_SET 480701 *** AXIS: Cntrl= 65786 (0x000100fa), Param= 5406 (0x0000151e) SPOILERS_SET . . . and 513695 *** EVENT: Cntrl= 65715 (0x000100b3), Param= 4608 (0x00001200) XPNDR_SET 513742 *** EVENT: Cntrl= 66036 (0x000101f4), Param= 0 (0x00000000) AP_VS_VAR_SET_ENGLISH 513742 *** EVENT: Cntrl= 66705 (0x00010491), Param= 0 (0x00000000) APU_OFF_SWITCH 513742 *** EVENT: Cntrl= 65715 (0x000100b3), Param= 4608 (0x00001200) XPNDR_SET 513773 *** EVENT: Cntrl= 66036 (0x000101f4), Param= 0 (0x00000000) AP_VS_VAR_SET_ENGLISH 513773 *** EVENT: Cntrl= 66705 (0x00010491), Param= 0 (0x00000000) APU_OFF_SWITCH 513773 *** EVENT: Cntrl= 65715 (0x000100b3), Param= 4608 (0x00001200) XPNDR_SET 513851 *** EVENT: Cntrl= 66036 (0x000101f4), Param= 0 (0x00000000) AP_VS_VAR_SET_ENGLISH . . . Is this an Aerosoft issue or something with my settings? John Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted August 21, 2017 Aerosoft Share Posted August 21, 2017 If FSUIPC is logging something I assume you can switch that off in FSUIPC. There are standard events, not bugs or anything. Link to comment Share on other sites More sharing options...
jer029 7 Posted August 21, 2017 Author Share Posted August 21, 2017 I'm aware I can turn off logging - I turned it on. What I don't understand is why it's showing continuous switch buttons being activated when none are being pressed, and the spoiler set when I don't believe I have set that to an axis. The spoiler would make sense if it's set on a joystick that doesn't have a delta set properly. I'll recheck this, but I didn't see that set in P3d controls as an axis. I'm not sure why a key setting would keep firing an event. Turning off the logging stops showing me the event - not preventing wasted processing time because the events are actually still firing. Perhaps it's just my system set up then. John Link to comment Share on other sites More sharing options...
Hans Hartmann [OLD] 1419 Posted August 21, 2017 Share Posted August 21, 2017 14 minutes ago, jer029 said: turning off the logging stops showing me the event - not preventing wasted processing time because the events are actually still firing. Perhaps it's just my system set up then. The events are fine as they are. However, logging wastes about 100 times as much processing time (if not more).... Link to comment Share on other sites More sharing options...
jer029 7 Posted August 21, 2017 Author Share Posted August 21, 2017 Thanks Hans, I don't keep logging activated. I just check now and again to see that things aren't firing unnecessarily: "The Delta is the value below which changes seen in the input will be ignored. It shouldn't normally be changed -- it's only normal purpose is to eliminate small scale jitter which has no bearing on the result but wastes a lot of processing time." - Pete Dowson (FSUIPC) Emphasis added, John Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted August 21, 2017 Aerosoft Share Posted August 21, 2017 Believe me sir, this is done on purpose and for good reason. It is does not indicate an error. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.