Joshua Che. 1601 Posted January 30, 2012 Share Posted January 30, 2012 Introduction: I have seen many people here due to nose drop or any other FBW problems, disable the FBW. I have use xml to program a FBW code using PID and many others. I have inserted my own pause logic as well to work in tadem with Aerosoft code. This FBW require FSUIPC. This gauge is in no way related to aerosoft and its for your own personal use. Upon the request of many people and support from the people who helped me like Gary from Project Airbus and FSDevelopers, I will release a incomplete version. Its not the best rendition but I guess it is good enough for daily flying. This is a complete new build. New Features / Differences from v0.8Side stick now command GLoadSide stick now command Roll rate.Rudder Auto-coordination included.Should elminate any autoland problemRudder is SO much betterPID controllers again to tune RAW joystick input sensitivity etc.And many others that I forgot. WARNINGS: THIS DOES NOT WORK WITH MERGES! BACKUP FIRST FSX MUST BE CLOSED WHEN INSTALLING REQUIREMENTS: Joystick REGISTERED FSUIPC for axis input. (This can be done away if aerosoft provide a dll module like the FADEC (which I have no access to) for axis input. Installation: THOSE WHO USED have ANY OLDER FBW VERSION MUST REINSTALL AIRBUS X Run the appropriate .exe patcher that will patch your files. There are four (one for now A320 only) patchers. Recommend to install one patcher first and test out then apply all. FSUIPC Required. FSUIPC Config FIles: LUA.zip INSTRUCTIONS: Extract the FSUIPC CONFIG FILES files in to FSXINSTALLDIRECTORY\Modules. AirbusXInstallInstructions.pdf Please feedback any praise or comments or criticism you have. Also, a little thanks post goes a long, long way. LATEST VERSION: V1.0alpha1g THOSE WHO USED have ANY OLDER FBW than V1.0alphaf VERSION MUST REINSTALL AIRBUSX FIRST DOWNLOAD: Direct from Aerosoft: FBWCODEBETAv1.0alpha1g.zip Mirror: http://dl.dropbox.com/u/33517934/FBWCODEBETAv1.0alpha1g.zip LUA Files: LUA.zip CHANGELOG: V1.0 alpha 1a - First Public Release V1.0 alpha 1b - Added A320 IAE Changed the way raw joystick data is handled by FBW. Joystick sensitivity changed. Flare added. Pitch and bank sensitivity addresed (More precise) . V1.0 alpha1c - Fixed compatibilty with More Callouts Uninstaller bugs fixed and detect installation beter. V1.0 alpha1d - PItch Trim imporvements. Added experimental A321 CFM. Patches Woes fix attempt Many more that I forgot. V1.0 alpha1e - Very beta stall protection Added experimental A321 IAE. PItch Trim Revisions. V1.0 alpha1f - Rewrite Trim and Pitch Commands Smoother Pitch commands V1.0 alpha1g - Rewrote Roll command Removed A321 IAE. Fixed all patch issues. Upcoming Versions (to be implemented) - Stall Protection (Not alpha floor, but it is to keep the AoA from reaching stall) - Overspeed Protection (Need to research) - Any other sugestions for FBW only? LEGAL STUFF This mod is released as FREEWARE. You may use and modify it in any way you wish, but you may NOT use it in any kind of money-making endeavor, and you may NOT publicly distribute any copies of it , whether modified or not, without my permission. Regards, Joshua Cheaerosoft.airbus.x.fbw.code.patcher-patchv1.0alpha1aA320CFM.zipFBWCODEBETAv1.0alpha1c.zipFBWCODEBETAv1.0alpha1d.zipFBWCODEBETAv1.0alpha1e.zipFBWCODEBETAv1.0alpha1f.zip 1 Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted January 30, 2012 Author Share Posted January 30, 2012 Reserved Link to comment Share on other sites More sharing options...
permastream 39 Posted February 17, 2012 Share Posted February 17, 2012 Hi Joshua. Thank you for the work you are doing to make this plane better. I've tryed to apply the last patch (alpha1c) It find the right path to the filel panel.cfg but cannot see it. The patcher-patch alpha1a can find the panel.cfg and work through. Have you an idea? Sean Edit: I've found out that the path suggested by the patcher was wrong. Instead of E:\Microsoft Flight Simulator X\SimObjects\Airplanes\Aerosoft Airbus X A320 CFM\Panel\AB_Systems was E:\SimObjects\Airplanes\Aerosoft Airbus X A320 IAE\Panel Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted February 18, 2012 Author Share Posted February 18, 2012 Hi Joshua. Thank you for the work you are doing to make this plane better. I've tryed to apply the last patch (alpha1c) It find the right path to the filel panel.cfg but cannot see it. The patcher-patch alpha1a can find the panel.cfg and work through. Have you an idea? Sean Edit: I've found out that the path suggested by the patcher was wrong. Instead of E:\Microsoft Flight Simulator X\SimObjects\Airplanes\Aerosoft Airbus X A320 CFM\Panel\AB_Systems was E:\SimObjects\Airplanes\Aerosoft Airbus X A320 IAE\Panel OK I found the problem and fix it will upload it today! Link to comment Share on other sites More sharing options...
AirbusDriver 2 Posted February 25, 2012 Share Posted February 25, 2012 Hi dudes, I'm back. Joshua, I'll read all old topic and then post a reply bye Link to comment Share on other sites More sharing options...
Marcel G. 14 Posted February 28, 2012 Share Posted February 28, 2012 OK I found the problem and fix it will upload it today! Still the same problem here Joshua.Please check that out. Thanks for all your work Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted February 29, 2012 Author Share Posted February 29, 2012 Still the same problem here Joshua.Please check that out. Thanks for all your work Would you do me a favour by copying the Log onto the clipboard and the paste it here. Thanks! EDIT: Try alpha1d first. Thanks! Link to comment Share on other sites More sharing options...
Marcel G. 14 Posted March 1, 2012 Share Posted March 1, 2012 Would you do me a favour by copying the Log onto the clipboard and the paste it here. Thanks! EDIT: Try alpha1d first. Thanks! Hi josh alpha1d is working perfectly.Thanks a lot. Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted March 2, 2012 Author Share Posted March 2, 2012 Hi josh alpha1d is working perfectly.Thanks a lot. No problem. Any feedback since I have not recieved one ? Link to comment Share on other sites More sharing options...
Guest cptawsom Posted March 2, 2012 Share Posted March 2, 2012 You haven't described what is different from 0.8f2, so that we know whether to try this out or not. Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted March 2, 2012 Author Share Posted March 2, 2012 PID and many others. AND This is a complete new build. As with new things, it is more precise and accurately simulating the FBW. New stuff includeSide stick now command GLoadSide stick now command Roll rate.Rudder Auto-coordination included.Should elminate any autoland problemRudder is SO much betterPID controllers again to tune RAW joystick input sensitivity etc.And many others that I forgot. Link to comment Share on other sites More sharing options...
dd_mario 0 Posted March 12, 2012 Share Posted March 12, 2012 HI Joshua, I used your old Version 0.82 and I´m a big fan of it. Now I want to try the new one. But I only have the unregisterd version of FSUPC. It was impossible to install. :-( Could you change this in further versions or was it my mistake. Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted March 16, 2012 Author Share Posted March 16, 2012 HI Joshua, I used your old Version 0.82 and I´m a big fan of it. Now I want to try the new one. But I only have the unregisterd version of FSUPC. It was impossible to install. :-( Could you change this in further versions or was it my mistake. The FBW requires Registered FSUIPC for axis input from your joystick. Without it, the FBW cant recieve your inputs. I really do not have the time now at this cruical year to do a module that can replace FSUIPC purpose. i think that you should uninstall this and revert back to FBW v0.8f2. Thanks alot for your interest. Link to comment Share on other sites More sharing options...
Ivek 4 Posted March 16, 2012 Share Posted March 16, 2012 Joshua ,thanks for your work. I try it. A little better. But for my opinion still slow joystick feedback control. I used combine with FSUIPC. Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted March 16, 2012 Author Share Posted March 16, 2012 Joshua ,thanks for your work. I try it. A little better. But for my opinion still slow joystick feedback control. I used combine with FSUIPC. In FSUIPC, try lowering your delta to 1 and see if there is any improvements. You may also want to calibrate your joystick. Also, Real World Airbus FBW do not actuate the flight controls like what you would expect in 737. if you want something not as realistic but more sensitive then use v0.8f2 Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted April 5, 2012 Author Share Posted April 5, 2012 New minor update coming soon: Revision to Pitch Trim Very beta stall protection Release expected by this sunday. Released! Link to comment Share on other sites More sharing options...
vali 31 Posted May 7, 2012 Share Posted May 7, 2012 I decided to try this mod also, but I get ''flickering'' on F/CTL pages for ailerons and elevator when I do the control check, then I can not control the plane.. ailerons and elevators are always oscillating and try to get back in their 0 position. Any idea of what could be the problem? I did like pdf tutorial says (or maybe I missed something...) (one mention, I don't have pedals for rudder, so I don't use/need rudder axis configured for now, eventually I use keyboard) Axis are recognized when I am in FSUIPC. Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted May 8, 2012 Author Share Posted May 8, 2012 I decided to try this mod also, but I get ''flickering'' on F/CTL pages for ailerons and elevator when I do the control check, then I can not control the plane.. ailerons and elevators are always oscillating and try to get back in their 0 position. Any idea of what could be the problem? I did like pdf tutorial says (or maybe I missed something...) (one mention, I don't have pedals for rudder, so I don't use/need rudder axis configured for now, eventually I use keyboard) Axis are recognized when I am in FSUIPC. Type this into your windows explorer %AppData%\Microsoft\FSX\controls. Zip or paste the standard.xml here. Double check your axis assignment is not assigned in FSX controls (NOT FSUIPC) . Link to comment Share on other sites More sharing options...
vali 31 Posted May 8, 2012 Share Posted May 8, 2012 I will do this in the afternoon, post it here, because I still didn't manage to get it right. Last evening I managed to get the elevators running but whatever I do, ailerons don't move. One question, calibration of the flight controls (elevators, ailerons) should be done also in FSUIPC? If yes, to get a better feel of the controls, there are some recommendations? Link to comment Share on other sites More sharing options...
vali 31 Posted May 8, 2012 Share Posted May 8, 2012 I attached the Standard.xml. Hopefully will help. Thanks! Edit: elevators work fine, I used LUA file from this forum for throttle, it works also fine, only ailerons not. I changed Lua FBWROLL with Axis Ailerons Set from FSUIPC and they work but try always to go back to normal position, so I suppose somewhere ailerons are still configured even if joystick is disabled in FSX config. Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted May 9, 2012 Author Share Posted May 9, 2012 I attached the Standard.xml. Hopefully will help. Thanks! Edit: elevators work fine, I used LUA file from this forum for throttle, it works also fine, only ailerons not. I changed Lua FBWROLL with Axis Ailerons Set from FSUIPC and they work but try always to go back to normal position, so I suppose somewhere ailerons are still configured even if joystick is disabled in FSX config. If you use FSUIPC calibration, I think it will directly bypass my FBW and hence flutter (my FBW command 0 because no input but FSUIPC command lets say 45 percent and so forth) Your FSX assignment seems fine. Strange... Screenshot your FSUIPC assignment for each Lua FBWROLL Lua FBWELEV Lua FBWRUD Link to comment Share on other sites More sharing options...
vali 31 Posted May 13, 2012 Share Posted May 13, 2012 Now with version V1.0 alpha1g everything works fine up to now, more testing in progress, many thanks for support Joshua. Link to comment Share on other sites More sharing options...
Robert Halmich 8 Posted May 16, 2012 Share Posted May 16, 2012 Hi Joshua, Nice work, I appreciate all your effort into improving the Airbus X however it does not work very well for me. I am using the Saitek Cessna Pro Yoke and Throttle and it worked flawlessly the first time, except for the throttle axis. The reverse levers engaged when I advanced the throttles or the throttles wouldn't move smoothly until they were past the CL detent. I tried FInn's throttle setup as per his thread then more issues arose. It is too bad that it does not work for me, perhaps that is why you wrote that a joystick is required. I still have my HOTAS Cougar and may have to bring that out of retirement. Again, thanks for all your hard work. Robert Link to comment Share on other sites More sharing options...
vali 31 Posted May 16, 2012 Share Posted May 16, 2012 I keep the throttles on FS settings because scripts from Finn doesn't work ok for me also (in fact I used reversers with F2 and Idle, CL and so on from the LUA scripts) and at landing, when I am doing Retard, A/THR is not disconnected. If reverse is engaged at advancing the throttles, you need to reverse the axis. Or you can try to do settings to use FSUIPC calibration instead of FS. Link to comment Share on other sites More sharing options...
Joshua Che. 1601 Posted May 16, 2012 Author Share Posted May 16, 2012 Hi Joshua, Nice work, I appreciate all your effort into improving the Airbus X however it does not work very well for me. I am using the Saitek Cessna Pro Yoke and Throttle and it worked flawlessly the first time, except for the throttle axis. The reverse levers engaged when I advanced the throttles or the throttles wouldn't move smoothly until they were past the CL detent. I tried FInn's throttle setup as per his thread then more issues arose. It is too bad that it does not work for me, perhaps that is why you wrote that a joystick is required. I still have my HOTAS Cougar and may have to bring that out of retirement. Again, thanks for all your hard work. Robert The throttle issue is not related to my FBW at all. Nevertheless, if you need help, Drop me a PM! Link to comment Share on other sites More sharing options...
Recommended Posts