simmyjiff 0 Posted January 20, 2021 Share Posted January 20, 2021 Hello Everybody, I seem to have a controller conflict between an Axis and Key Assignments causing engine speeds to increase rapidly from N1 19.1% to N1 37.2%. I'm flying a Frankfurt to Heathrow flight plan in a AS A319, (P3Dv4), using normal procedures. There was a good start to both engines, satisfactorily achieving 19.1% N1, However when applying FULL LEFT in the After Start flight control test, N1 rose to 37.2%? I wish I could relate this to a particular cause but regrettably I can't. Any help would be appreciated, copes of the screen print are attached showing both events. Thanks Jim Please login to display this image. Please login to display this image. Link to comment Share on other sites More sharing options...
Deputy Sheriffs masterhawk 799 Posted January 21, 2021 Deputy Sheriffs Share Posted January 21, 2021 Hi, you have to check your key and axis bindings in the sim setup. Link to comment Share on other sites More sharing options...
simmyjiff 0 Posted January 21, 2021 Author Share Posted January 21, 2021 Hi masterhawk,m Yeah done that. Keyboard Assignments: Nothing against Increase throttle (F3 and NUM9), No Aileron bindings either. Axis Assignments: Engine 1 Throttle Axis Z Axis, Engine 2 Throttle Axis Rx Axis. Calibration settings to Default. Isn't it strange that N1% increases to a certain number? could it be anything in the Registry? Tahnks Link to comment Share on other sites More sharing options...
Deputy Sheriffs masterhawk 799 Posted January 21, 2021 Deputy Sheriffs Share Posted January 21, 2021 It’s really strange. But the bus takes the axis direct from sim. How does it work in other aircraft? Link to comment Share on other sites More sharing options...
DaveCT2003 2553 Posted January 21, 2021 Share Posted January 21, 2021 I remember reading about this years ago in the Beta. I don't remember anything more than that. Link to comment Share on other sites More sharing options...
simmyjiff 0 Posted January 22, 2021 Author Share Posted January 22, 2021 Hi Guys, and thanks for your comments. Yes Dave, I think you're right, when this problem first started earlier this week, I trolled the Web a found a couple of articles on the same subject and yes, they were years old, I'll try and find them again. In the meantime, I've started testing on other aircraft, and it appears the problem only exists with buses with CFM engines, IAE engines appear normal, interesting? from what I recall of that earlier post this seems to be replicating that problem.# I will however carry on through today and check on other aircraft types and come back to you tomorrow, for information I have tested the A2A Cessna 172, and that looks fine! Dave, I would be obliged if you could rack your brain again about that article for me, it may have the answer? Jim Link to comment Share on other sites More sharing options...
simmyjiff 0 Posted January 22, 2021 Author Share Posted January 22, 2021 26 minutes ago, simmyjiff said: Hi Guys, and thanks for your comments. Yes Dave, I think you're right, when this problem first started earlier this week, I trolled the Web a found a couple of articles on the same subject and yes, they were years old, I'll try and find them again. In the meantime, I've started testing on other aircraft, and it appears the problem only exists with buses with CFM engines, IAE engines appear normal, interesting? from what I recall of that earlier post this seems to be replicating that problem.# I will however carry on through today and check on other aircraft types and come back to you tomorrow, for information I have tested the A2A Cessna 172, and that looks fine! Dave, I would be obliged if you could rack your brain again about that article for me, it may have the answer? Jim Btw, The A320 Family Professional Bundle, is a new reinstall Link to comment Share on other sites More sharing options...
simmyjiff 0 Posted January 22, 2021 Author Share Posted January 22, 2021 Okay, Out of 8 Air Buses, 4 had the problem, (those with CFM Engines) the remaining 4 worked okay, (these had the IAE engines) Other Aircraft tested, A2A 172 Cessna by Carenado, A 5252CJ also By Carenado and the EMB505 Phenom, all worked satisfactorily. Thanks for your help Jim Link to comment Share on other sites More sharing options...
simmyjiff 0 Posted January 24, 2021 Author Share Posted January 24, 2021 ??? Link to comment Share on other sites More sharing options...
Deputy Sheriffs mopperle 4162 Posted January 24, 2021 Deputy Sheriffs Share Posted January 24, 2021 2 hours ago, simmyjiff said: ??? Maybe time to make a complete fresh install of your Sim, the Bus and maybe even Windows? Nobody else is experiencing your problem, nobody can recreate it, so it is quite obvious that something is broken in your setup. Where is your P3D installed? Where is the Bus installed? Link to comment Share on other sites More sharing options...
simmyjiff 0 Posted January 26, 2021 Author Share Posted January 26, 2021 On 1/24/2021 at 2:08 PM, mopperle said: Maybe time to make a complete fresh install of your Sim, the Bus and maybe even Windows? Nobody else is experiencing your problem, nobody can recreate it, so it is quite obvious that something is broken in your setup. Where is your P3D installed? Where is the Bus installed? Wow! That seems a drastic move but Ok, and thanks for your comment Installation: C:\Program Files\Lockheed Martin\Prepar3D v4 C:\Users\Jim Smith\Documents\Aerosoft Carried out a fresh install of the Bus last Monday (18th Jan 2021) For information I am flying the flying the planes with the IAE engines with no problems. l.. very odd Thanks Jim Link to comment Share on other sites More sharing options...
Deputy Sheriffs mopperle 4162 Posted January 26, 2021 Deputy Sheriffs Share Posted January 26, 2021 Regarding the installation of P3D and its addons the following is recommended: - P3D: never install it under C:/program files; this folder is for security reasons treated specially by Windows and sometimes other apps can not write to this folder. Simply install it to something like C:/P3D - Addons: Those addons following P3D guidelines and allowing you to choose any installation directory should be installed to something like C:/P3D Addons; do NOT install them into the P3D folder and also not in the documents folder (other then required by the installer). Link to comment Share on other sites More sharing options...
simmyjiff 0 Posted January 28, 2021 Author Share Posted January 28, 2021 Great, Thanks to you all for your help, best Regards Jim Link to comment Share on other sites More sharing options...
Deputy Sheriffs mopperle 4162 Posted January 28, 2021 Deputy Sheriffs Share Posted January 28, 2021 Because we believe this topic has been answered we have closed it. If you have any more questions feel free to open a new topic. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.