Jump to content

Archived

This topic is now archived and is closed to further replies.

roland_lfor

Robin and P3DV2 [SOLVED]

Recommended Posts

Hello,

I installed the Robin under the new Prepar3D V2 and observed 2 issues :

- I'ts like some invisible wheel shocks are permanently attached to the aircraft. When I push full throttle, the plane can not move forward on the ground.

- the cockpit lighting appears red

Do you have any fix for them, especially the brake problem ?

Thanks

Roland

Share this post


Link to post

There is no reason why the brakes shouldn´t work.

Try to press the barke bedals while releasing the parkingbrake.

I´m not sure what's wrong with the cockpit lighting

Finn

Share this post


Link to post

I have reinstalled :

the red lighting is fixed, but I'm unable to solve the permanent brake issue.

I'm curious to see if someone else observe this problem as well.

Share this post


Link to post

I have reinstalled :

the red lighting is fixed, but I'm unable to solve the permanent brake issue.

I'm curious to see if someone else observe this problem as well.

I have the same problem but without red lighting

Share this post


Link to post

I am not sure, if this is possible, because nobody of the Robin-develpoers runs P3DV2 at the moment. But the issue is strange, because the parking brake is not special at all as far as I remember.

Share this post


Link to post

I am not sure, if this is possible, because nobody of the Robin-develpoers runs P3DV2 at the moment. But the issue is strange, because the parking brake is not special at all as far as I remember.

I confirm the issue in P3DV2.

Plane does not move when on the ground, feels indeed as if the parking brake is on.

I tried all combinations of braking, park brake set and release, using rudder pedals and keys.

You can fly the plane (loading it in a flight situation), but you cannot land the Robin as it crashes immediately upon touching the ground.

Share this post


Link to post

I am sorry, no idea at the moment. But I'll consider to get P3D.

That is a very good idea. I suppose Aerosoft wants to go the way of the future, now P3DV2 is in fact the next iteration of FS, let's call it FS11. But now with very responsive and active support, something I cannot remember from Microsoft.

Share this post


Link to post

Perhaps it's not a brake problem, but a ground/friction coefficient ?

How can I set the friction to 0 for a test ?

Share this post


Link to post

That is a very good idea. I suppose Aerosoft wants to go the way of the future, now P3DV2 is in fact the next iteration of FS, let's call it FS11. But now with very responsive and active support, something I cannot remember from Microsoft.

Well, I don't think, that it will be something like "FS11" due to the current available licensensing options, but this shouldn't be a discussion pro or contra P3D.

Share this post


Link to post

Any news according to the braking problem?

Just bought my boxed Robin but now i will wait to buy P3D2 until it's fixed.

Share this post


Link to post

No news at the moment. Nobody of us has the time to look into P3DV2 at the moment and no idea, what it could be.

At the moment, the product seems to beincompatible with V2.

Bests, Joachim

Share this post


Link to post

hi there, same Problem on the ground here. No way to start and also no way to land this fine aircraft in P3Dv2.

As you are selling this product as "auch kompatibel mit Prepar3D" without mentioning any versions, it would be more then just nice to have this Problem fixed.

best regards

Simon

Share this post


Link to post

When the Robin was sold, it was compatible with P3D available at that time. P3Dv2 was lightyears away, so do not expect to much.

Share this post


Link to post

I finally found a turnaround:

- Open the Aircraft file

- Search the [brake] section

- Comment (//) the 'hydraulic_system_scalar' line

So the section should be like this:

[brakes]
toe_brakes_scale        = 1.0
//hydraulic_system_scalar    = 1.0
differential_braking_scale    = 0.8
parking_brake            = 1

Envoy !

I suspect a bug in P3Dv2...

Share this post


Link to post
Guest
This topic is now closed to further replies.

×
×
  • Create New...