simon747 98 Posted September 2, 2010 Share Posted September 2, 2010 Hi, I use a small 2D panel called FDSFX panel addon for my cabin sounds; ie FA sounds etc. I was wondering if there is a trick to installing a new window or panel for this small addon panel for sounds. Can't get it to work. I have followed all the set-up steps as with the default ac, but no luck with the bus? I believe it would be a smilair set-up to installing the Garmen GPS etc to the bus? When I click on shift plus the corresponding numerical key assiagned in the bus a message comes up: user tip: no panel is mapped to the panel 7 key. The following panels are available on this aircraft: Panel 1 (Shift+1): Main Panel Here is the file: I have used in FSX for years with VC's with no problem. http://www.flightsim...me=FDSFXPNL.ZIP Cheers guys so far; have not flown yet, but I like!!! Simon Link to comment Share on other sites More sharing options...
cbd80 258 Posted September 2, 2010 Share Posted September 2, 2010 It should be the same procedure. Have you defined your new window in the VC section of the panel.cfg? Chris Link to comment Share on other sites More sharing options...
simon747 98 Posted September 2, 2010 Author Share Posted September 2, 2010 It should be the same procedure. Have you defined your new window in the VC section of the panel.cfg? Chris Aghh; good call; maybe not; let me check... Link to comment Share on other sites More sharing options...
simon747 98 Posted September 2, 2010 Author Share Posted September 2, 2010 Aghh; good call; maybe not; let me check... Hey Chris, Thanks for your help buddy:) What do you mean by define? All I am doing is: Putting the below gauge files in the panel.cfg: gauge00=FDSFX_01_gate!switch, 49,89,30,51 gauge01=FDSFX_02_airport!switch, 111,89,30,51 gauge02=FDSFX_03_muzak1!switch, 174,89,30,51 gauge03=FDSFX_04_muzak2!switch, 235,89,30,51 gauge04=FDSFX_05_muzak3!switch, 295,89,30,51 gauge05=FDSFX_06_turbulence on!switch, 357,89,30,51 gauge06=FDSFX_07_turbulence off!switch, 419,89,30,51 gauge07=FDSFX_08_gate departure!switch, 49,190,30,51 gauge08=FDSFX_09_pushback!switch, 111,190,30,51 gauge09=FDSFX_10_safety message!switch, 174,190,30,51 gauge10=FDSFX_11_safety video!switch, 235,190,30,51 gauge11=FDSFX_12_takeoff!switch, 295,190,30,51 gauge12=FDSFX_13_climb!switch, 357,190,30,51 gauge13=FDSFX_14_cruise!switch, 419,190,30,51 gauge14=FDSFX_15_meal service!switch, 49, 298 ,30,51 gauge15=FDSFX_16_movie!switch, 111,298,30,51 gauge16=FDSFX_17_begin descent!switch, 174,298,30,51 gauge17=FDSFX_18_on approach!switch, 235,298,30,51 gauge18=FDSFX_19_on final!switch, 295,298,30,51 gauge19=FDSFX_20_taxi to gate!switch, 357,298,30,51 gauge20=FDSFX_21_gate arrival!switch, 419,298,30,51 AND Putting this in there: [Window01] file=FDSFX.bmp size_mm=500 position=0 visible=0 ident=122757 Not sure how to define...? Link to comment Share on other sites More sharing options...
cbd80 258 Posted September 2, 2010 Share Posted September 2, 2010 Simon. Sorry, nothing should go under the VC section! The only thing you have missed there is: [Window Titles] WindowXX=FlightDeck SFX Panel So, you should have at the top under Window00: Window01=FlightDeck SFX Panel Then after [Views] and [Window00] you should have: [Window01] file=FDSFX.bmp size_mm=500 position=0 visible=0 ident=122757 gauge00=FDSFX_01_gate!switch, 49,89,30,51 gauge01=FDSFX_02_airport!switch, 111,89,30,51 gauge02=FDSFX_03_muzak1!switch, 174,89,30,51 gauge03=FDSFX_04_muzak2!switch, 235,89,30,51 gauge04=FDSFX_05_muzak3!switch, 295,89,30,51 gauge05=FDSFX_06_turbulence on!switch, 357,89,30,51 gauge06=FDSFX_07_turbulence off!switch, 419,89,30,51 gauge07=FDSFX_08_gate departure!switch, 49,190,30,51 gauge08=FDSFX_09_pushback!switch, 111,190,30,51 gauge09=FDSFX_10_safety message!switch, 174,190,30,51 gauge10=FDSFX_11_safety video!switch, 235,190,30,51 gauge11=FDSFX_12_takeoff!switch, 295,190,30,51 gauge12=FDSFX_13_climb!switch, 357,190,30,51 gauge13=FDSFX_14_cruise!switch, 419,190,30,51 gauge14=FDSFX_15_meal service!switch, 49, 298 ,30,51 gauge15=FDSFX_16_movie!switch, 111,298,30,51 gauge16=FDSFX_17_begin descent!switch, 174,298,30,51 gauge17=FDSFX_18_on approach!switch, 235,298,30,51 gauge18=FDSFX_19_on final!switch, 295,298,30,51 gauge19=FDSFX_20_taxi to gate!switch, 357,298,30,51 gauge20=FDSFX_21_gate arrival!switch, 419,298,30,51 That should do it. Worked for me Remember you will have to do this in each of the Airbus X panel folders and copy in the .bmp Chris Link to comment Share on other sites More sharing options...
Marcel G. 14 Posted September 3, 2010 Share Posted September 3, 2010 Simon. Sorry, nothing should go under the VC section! The only thing you have missed there is: [Window Titles] WindowXX=FlightDeck SFX Panel So, you should have at the top under Window00: Window01=FlightDeck SFX Panel Then after [Views] and [Window00] you should have: [Window01] file=FDSFX.bmp size_mm=500 position=0 visible=0 ident=122757 gauge00=FDSFX_01_gate!switch, 49,89,30,51 gauge01=FDSFX_02_airport!switch, 111,89,30,51 gauge02=FDSFX_03_muzak1!switch, 174,89,30,51 gauge03=FDSFX_04_muzak2!switch, 235,89,30,51 gauge04=FDSFX_05_muzak3!switch, 295,89,30,51 gauge05=FDSFX_06_turbulence on!switch, 357,89,30,51 gauge06=FDSFX_07_turbulence off!switch, 419,89,30,51 gauge07=FDSFX_08_gate departure!switch, 49,190,30,51 gauge08=FDSFX_09_pushback!switch, 111,190,30,51 gauge09=FDSFX_10_safety message!switch, 174,190,30,51 gauge10=FDSFX_11_safety video!switch, 235,190,30,51 gauge11=FDSFX_12_takeoff!switch, 295,190,30,51 gauge12=FDSFX_13_climb!switch, 357,190,30,51 gauge13=FDSFX_14_cruise!switch, 419,190,30,51 gauge14=FDSFX_15_meal service!switch, 49, 298 ,30,51 gauge15=FDSFX_16_movie!switch, 111,298,30,51 gauge16=FDSFX_17_begin descent!switch, 174,298,30,51 gauge17=FDSFX_18_on approach!switch, 235,298,30,51 gauge18=FDSFX_19_on final!switch, 295,298,30,51 gauge19=FDSFX_20_taxi to gate!switch, 357,298,30,51 gauge20=FDSFX_21_gate arrival!switch, 419,298,30,51 That should do it. Worked for me Remember you will have to do this in each of the Airbus X panel folders and copy in the .bmp Chris Thats my config and it es working here you got a look into my aircraft.cfg [Window Titles] Window00=Main Panel Window01=FlightDeck SFX Panel [Views] VIEW_FORWARD_WINDOWS=MAIN_PANEL VIEW_FORWARD_DIR=0.0,0.0,1.0 //-------------------------------------------------------- [Window00] file=Panel_2D.bmp size_mm=800, 600 BACKGROUND_COLOR=0,0,0 visible=0 ident=MAIN_PANEL // --------------------------------------------------------- [Window01] file=FDSFX.bmp size_mm=500 position=0 visible=0 ident=122757 gauge00=FDSFX_01_gate!switch, 49,89,30,51 gauge01=FDSFX_02_airport!switch, 111,89,30,51 gauge02=FDSFX_03_muzak1!switch, 174,89,30,51 gauge03=FDSFX_04_muzak2!switch, 235,89,30,51 gauge04=FDSFX_05_muzak3!switch, 295,89,30,51 gauge05=FDSFX_06_turbulence on!switch, 357,89,30,51 gauge06=FDSFX_07_turbulence off!switch, 419,89,30,51 gauge07=FDSFX_08_gate departure!switch, 49,190,30,51 gauge08=FDSFX_09_pushback!switch, 111,190,30,51 gauge09=FDSFX_10_safety message!switch, 174,190,30,51 gauge10=FDSFX_11_safety video!switch, 235,190,30,51 gauge11=FDSFX_12_takeoff!switch, 295,190,30,51 gauge12=FDSFX_13_climb!switch, 357,190,30,51 gauge13=FDSFX_14_cruise!switch, 419,190,30,51 gauge14=FDSFX_15_meal service!switch, 49, 298 ,30,51 gauge15=FDSFX_16_movie!switch, 111,298,30,51 gauge16=FDSFX_17_begin descent!switch, 174,298,30,51 gauge17=FDSFX_18_on approach!switch, 235,298,30,51 gauge18=FDSFX_19_on final!switch, 295,298,30,51 gauge19=FDSFX_20_taxi to gate!switch, 357,298,30,51 gauge20=FDSFX_21_gate arrival!switch, 419,298,30,51 // --------------------------------------------------------- Hope i can help Regards Link to comment Share on other sites More sharing options...
simon747 98 Posted September 3, 2010 Author Share Posted September 3, 2010 Thanks guys for your help. That did it got it to work!! Simon Link to comment Share on other sites More sharing options...
Recommended Posts