Jump to content


  • Content Count

  • Joined

  • Last visited

Community Reputation

3 Neutral

About apilot01

  • Rank
    Flight Student - Groundwork

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Final piece of information - I did not need to use the Aerosoft purchase key to make the install run. Thanks again.
  2. Dear Joe, Thank you very much, I now have FSC9 on my hard drive. Your advice was exactly right. I thought it a bit odd that, despite all the warnings about not installing into C/Prog Files, the default installation location in the set up was..C/Prog Files ! (I am using Win7) No matter, alles ist in ordung! Danke.
  3. Dear Joe, Thank you very much for your help. I have downloaded using the link you have shown - the folder you have shown is completely different to the Aerosoft FSC 9.2 download folder. This new folder contains the FSCSetup.exe file. I have to go out this evening so cannot progress now but I wil report back without fail tomorrow. I am very grateful for your prompt and useful help. Thank you.
  4. Dear Joe, Thank you for your reply. You don't know how embarassed I am to tell you this but I can't make it install. I have downloaded the folder from the Aerosoft site again just now, unzipped the download directly into my FSC folder which is located at C:/FSC. As stated before I cannot see the FSCSetup.exe file as described in the extract from the PDF file shown below "FlightSim Commander will be installed by calling FSCSetup. Follow the instructions on the screen. After the program has been successfully installed, you can start it directly from its directory by clicking on Fsc
  5. Thank you for your reply, but where is the file? From the PDF file it says I have run the FSCSetUp file and follow the instructions. But, as previuosly described, I do not see a FSCSetUp file so I cannot run it. Hence the question. Any suggestions, please.
  6. I have been previously using FSC v 9.0 and upgraded to 9.1. I have now downloaded the new version 9.2 and to avoid any conflicts have uninstalled 9.1 and copied 9.2 into my C/FSC folder. Looking in the Installation .PDF I see a reference to a file FSCsetup, but looking at my downloaded files in my C/FSC folder I do not see this file anywhere. I have the following Folders:- Map, Support, Tool and the following files:- FSC.exe, FSCDbManager.exe, FSCFSXCFG.exe, FSCP3DCFG.exe but no FSCSetup. Can you please tell me where it is? Thank you.
  7. Dear Shaun, I am sorry but I do not understand what this means. What should I do to a) make FSX run and 'b) make the VHHX files "visible" to FSCommander? Thank you, Tregarth
  8. I looked in C:\FSX\Addon Scenery\FyTampa-HongKong and found 3 files afx_2HHX_flytampa_aiship.bgl , afx_VHHX_approach.bgl and AFX_VHHX_sdk_aerostat.bgl I moved the _approach file from the FlyTampa-HongKong scenery folder and pasted it into C\FSX\Add-on Scenery folder (ASF), closed Win Explorer and started FSX. Saw a window "Building database for new scenery files". The intro music played and then saw "Fatal Error" message. I removed the _approach file from the ASF, put it back into the Hong Kong scenery folder and restarted FSX. Now see a message "Scenery.cfg file error. Local sce
  9. Dear Shaun, Thanks for your help. I have looked for the Hong Komg Scenery, there are 2 folders for HK scenery; they are C:\FSX\Addon Scenery\FyTampa-HongKong and C:\FSX\Addon Scenery\FlyTampa-HongKong_LC FyTampa-HongKong contains 3 Folders, Doc, Scenery andTexture; FlyTampa-HongKong_LC contains only a scenery folder. I have searched my C driver for an AFCAD file but cannot see one. I am running FSX on my "Main" PC and FSCommander on a second PC which is networked to the Main PC, normally they work perfectly but not for Hong Kong. Should I copy one of the HK files on my Main PC
  10. Thanks for the reply. Yes. In fact I had run it before I updated the FSC.exe and FSCDbManager files. I updated both, ran the DB Manager with FSX running (so the programs could "talk" to each other) with the result you can see. I then ran it a second time but with no improvement. As I said before, the scenery shows in FSX and the ILS feathers show in the FSX GPS. Thank you, Tregarth
  11. I am using FSC 9 which I have just updated using the latest FSC.Exe and DBManager Files. I have installed Fly Tampa's Hong Kong add-on (distributed by Aerosoft) but I do not see the airport when I run FSC. Please see attached screen grab. The airport shows in FSX's GPS screen but not in FSC What can I do to make this airport appear, please? I am using FSX with Acceleration and Win 7. Thank you, Tregarth
  12. I cannot make saved FSC 9 flight plans, which are in FSC 9 on my Client, Acer-PC, appear in my FSX Flight Plan folder (C:\Users\Clive\My Docs\Flight Sim X files) in my Main PC. Both PC's are running Win 7 Home Premium. I have networked 2 PC's one running FSX (Clive-PC) the other FSC (Acer-PC). When I turn on the PC's and look in Network on my Acer-PC (my client PC which has FSC on it) I see a network icon with (\\Clive-PC) (Y:) Below this I see a network icon folder: Flight Simulator X Files Opening this folder I see my Saved Flight s which have been saved using the FSX Flight Planner.
  13. Dear Jim, Thanks for the help. In fact I had to sort out some security settings on my FSX folder which was not easy but someone sorted them out for me. I have now run FSC and have a message "Unable to connect to Flight Sim Msg #2". I have reported this to Herr Heine so I am hoping he can tell me where I am going wrong. Thanks again, Clive 3.87 km SW of EGTF
  14. Thanks, I have followed the instructions on pages 100 - 104 (Appendix Network) in the FSC PDF help guide to the letter. These were written for Win XP so have had to adapt them for Win 7 but on the Main (FSX containing PC) I have set FSX Properties to Network File and Folder Sharing to MS FSX - Shared and the Network Path is \\User-PC\MS FSX. Avanced Sharing Permissions is set to Everyone and Full Control is ticked. So I think that PC is OK since these are the instructions from FSC. However, on my Acer client FSC containing PC when I start up I see the screen shown in the attached Screen
  15. Dear Jim, Thanks for your help, I appreciate it. I did as you said and FSC now works on my NetBook. Unfortunately, my Network is not working properly so I am still struggling. But, I will persevere. Tregarth.
  • Create New...