Kevin_FS 0 Posted September 3, 2009 Share Posted September 3, 2009 Hi there, I checked several topics on this forum to get rid of the bouncing problem with the PMDG 747. I already used the "Repair for push" function several times, but no improvements yet. I also tried to change the static_Pitch=0.0 but no results. Here you can see my aircraft.cfg file: //AES Orgvalue:static_pitch = -0.14 static_pitch=.55 //AES Orgvalue:static_cg_height = 11.90 static_cg_height=10.55 gear_system_type=0 Does anybody else experience the same problems with the PMDG 747-400 (FSX version)? Kind regards, Kevin Link to comment Share on other sites More sharing options...
Rafal Haczek 1612 Posted September 3, 2009 Share Posted September 3, 2009 I don't have it bouncing, so try mine: For the intelliscene: [Descr] Type=B744 [Geom] Nosegear= 26.9 Door1=-2.8, 24.85, 4.4, 5 Door2=-2.85, 15.35, 4.6 Door4=-2.3,-21.1, 4.85,-10 Front= 1.35, 21.1, 2.45 Rear= 1.25,-10.7, 2.6 For the aircraft config's contact points: //AES Orgvalue:static_pitch = -0.29 static_pitch=-.41 //AES Orgvalue:static_cg_height = 12.09 static_cg_height=11.78 Maybe it will work for you. You can always try. Best regards, Rafal Link to comment Share on other sites More sharing options...
Tomaz 10 Posted February 3, 2011 Share Posted February 3, 2011 I tired this but it's still bouncing. Any other solution? Link to comment Share on other sites More sharing options...
Verified Developer OPabst 2091 Posted February 3, 2011 Verified Developer Share Posted February 3, 2011 Did you reload the aircraft, after you changed the values? If the value fits, you can simple check, when you switch to and from the SLEW Modus, when the aircraft change his position up/down, then the value is wrong and needs to be ajusted a little bit. Often it is the Static_pitch, which is maybe better =0 or the Static_cg_Height value is to low or high. Link to comment Share on other sites More sharing options...
Tomaz 10 Posted February 3, 2011 Share Posted February 3, 2011 Thank's, I'll try! I changed the values when I was not in FSX, so yes, it was reloaded. Link to comment Share on other sites More sharing options...
Verified Developer OPabst 2091 Posted February 3, 2011 Verified Developer Share Posted February 3, 2011 Í just test the PMDG B747 in full and empty config in FSX and I see no issues with the following Values: static_pitch = -0.14 static_cg_height = 11.90 More I can't say. Link to comment Share on other sites More sharing options...
Tomaz 10 Posted February 9, 2011 Share Posted February 9, 2011 This is for those values in lines with "//" in front or without? Because it's still bouncing. Link to comment Share on other sites More sharing options...
Verified Developer OPabst 2091 Posted February 9, 2011 Verified Developer Share Posted February 9, 2011 This is for those values in lines with "//" in front or without? Because it's still bouncing. The lines with //AES are only the backuped orignal values, not readed by the FS Link to comment Share on other sites More sharing options...
Tomaz 10 Posted February 23, 2011 Share Posted February 23, 2011 It works! No more bouncing. Thanks! Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted February 24, 2011 Aerosoft Share Posted February 24, 2011 It works! No more bouncing. Thanks! Thanks for letting us know, over and out. Link to comment Share on other sites More sharing options...
Recommended Posts