Jump to content
Will C

OFP shows altimeter setting in hectopascals, not inHg

Recommended Posts

Hi, I posted on this before but now I have more information. The issue is that PFPX calls TOPCAT for the takeoff and landing data, and then brings the altimeter setting back in hectopascals, which gets passed to the OFP, even when the airport is located in a region in which inches of mercury would be preferred.

 

Attached is a screenshot of PFPX calling TOPCAT for takeoff information from Chicago O'Hare. You can see that PFPX/TOPCAT is fetching the altimeter setting in inches of mercury, and interpreting the METAR correctly - you'll see that under "Pressure," the correct numbers 30.06 are displayed. 

 

However, when you look at the results window (this is the information that TOPCAT will append to the OFP), you'll see that the altimeter setting is in hectopascals ("QNH 1018"). You'll see it in the line that reads:

 

TEMP +2C QNH 1018 WIND 130/12 (09KT HW) (emphasis added)

 

That line is brought into the PFPX flight plan verbatim.

 

I'm guessing that TOPCAT is looking at a config setting somewhere that requests results be given in hPa, but for the life of me I can't see where that would be. The PFPX file for the aircraft I'm using has the units set at feet and pounds. Under TOPCAT performance module, the file that is called is Boeing 747-400 RB211-524H, but I'm not sure what that links to or even if it's the problem. Within TOPCAT, I have only one aircraft in the aircraft database, and under "Aircraft Details," the pressure units are listed as inches of mercury.

 

Inside the TOPCAT "Aircraft" folder, the files are unreadable to me (i.e., not readable by a standard text editor). Inside the TOPCAT "Configurations" folder,  I can see some readable configurations but I can't see a line for setting a preference for the altimeter setting.

 

That's all I can think of. Can anyone help me get TOPCAT to send inHg to PFPX? Thanks!

 

Example.jpg

Share this post


Link to post
Share on other sites

I don't believe you can change the pressure configuration within Topcat.

 

Using the main program you can see hPa as the main function with the inHg equivalent displayed:

 

capture_001_17022020_161713.thumb.jpg.267536b3f836a1645ac0706daefb4b81.jpg

 

If you call up the results table you'll also see the hPa figure in use which is relayed back to PFPX:

 

TAKE-OFF KORD/ORD  RWY 10L  TORA 3962M            
G-ZESA  BOEING 747-400 RB211-524H
CHICAGO OHARE INTL                                

TEMP +2C   QNH 1018   WIND 110/09 (08KT HW)

------------------  CONDITIONS  -------------------
TOW 216523 KG   FLAPS 10   THRUST TO2   RWY DRY
AIR COND ON   ANTI ICE ON OR OFF

------------------  FULL THRUST -------------------
   +2C 271020 OBS(B) 114-121 121 141   2221M   1.57

----------------  REDUCED THRUST  -----------------
  +69C 234034 OBS(B) 127-129 129 139   1054M   1.37
  +70C 231976 CLIMB    129   129 139    980M   1.37
  +71C 227989 CLIMB    129   129 139    902M   1.37
  +72C 224001 CLIMB    129   129 139    823M   1.37
//+73C 220102 CLIMB    129   129 139    740M   1.37

***************************************************
DO NOT EXCEED MAX STRUCT TAKE-OFF WGHT OF 396894 KG
***************************************************

------------------  ENGINE OUT  -------------------
"AT 2200' LT TO HP 'OBK' 113.0" (092 INBD RT)

---------------------- END  -----------------------

 

 

Share this post


Link to post
Share on other sites

I guess it can't be changed. At least it's good to know for sure. 

 

Thanks again!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...