[Scenery Library AES Basepack position]

Oliver

Thanks for the answer - so AES Base pack must always be at Number 1 in the Scenery Library?

I never saw this message in ver 2.06 and earlier!!

I've just used ver 2.07 with Aerosoft's German Airports Vol 3 (+MTX 5.3) - awesome.

I am writing a review on Dirk Stuck's Ground Traffic X and I found a slight interaction between AES and GTX which to me didn't detract from the experience, they can co-exist together.

Thanks again

Regards

PeterH

[No menu in fsx]

Bruce

Thanks for that tip - I had the same issue post 2.07 but not seen in 2.06 - lucky I guess.

Regards

PeterH

[Scenery Library AES Basepack position]

Hi Oliver

Since upgrading to ver 2.07 each time I open FSX I get a message asking me to ensure that the AES basepack has top priority in the FSX scenery library and it does it for me automatically. Will I always get this message and does AES always have to be a position 1 in the scenery library?

Thanks

PeterH

[BM Take-Off Weight]

Joachim

Those weights work perfectly

Thanks

PeterH

[BM Take-Off Weight]

Joachim

Thanks - I'll adjust for every flight.

Regards

PeterH

[BM Take-Off Weight]

James

Thanks for that - further testing shows it has no effect on take-off performance.

Regards

PeterH

[BM Take-Off Weight]

Hi Support

Any response for this please?

Thanks

pH

[BM Take-Off Weight]

Hi

I notice in the aircraft payload menu for the BM that it is 74 (approx 34Kg) pounds overweight.

Is this due to water ballast being full every time FSX starts?

It doesn't seem to affect take-off performance.

The un-powered glider is only 8 pounds (approx 3.7Kg) overweight.

Is it anything to worry about? - Just ignore it?

PeterH

[FSX stops working as soon as I attempt to load Discus glider]

Joachim

I tried again and the "crash" occurs with the engine stowed and me increasing the throttle on my Saitek X-52, but it is intermittent it does not occur on every flight and it is only the BM. Probably idiosyncratic.

Regards

PeterH

[FSX stops working as soon as I attempt to load Discus glider]

Joachim

Thanks for that.

The CTD seems to have resolved itself due to me being more familair with the glider. I was trying to start the engine when it had been stowed and that seemed to be the issue.

Thanks again for the assistance.

Regards

PeterH

[FSX stops working as soon as I attempt to load Discus glider]

Mathijs & B21

Many thanks for the info.

This is awesome to fly and it is a quantum leap over the default glider.

Any tips on the "SOUNDS" question?

Regards

PeterH

[FSX stops working as soon as I attempt to load Discus glider]

Mathjis

Just took delivery of the Discus - awesome.

In the sticky notes above wrt water ballast you state: "use the aircraft menu to empty it when desired". Silly question but how do you access the "Aircraft Menu".

Sounds: Are there any tips or tricks on how to use the 200 or so additional sounds as referenced in the manual under Aerosoft Sound Control? For example what is the "ID Code"?

Is the "STATIC PORT SWITCH", the same as the "Flight Pressure Nozzle", and the same as the "Static Source"?

Just to report I have had two CTDs with the BM only when attempting to stow the engine or reduce the throttle (in flight), but I was not quick enough to see the body of the error and will try to reproduce. The other models seem fine.

Thanks

PeterH

[Beaver FSX and FSForce Trim Gauge]

Hi Manuel ansd Shaun

Good suggestion re transparent/blank panel- will try and report back.

Shaun - Yes it was the developer who suggested I posted here in case there was a simple fix such as that suggested by Manuel.

Thanks again

PeterH

[Beaver FSX and FSForce Trim Gauge]

Hi Support

I am a registered owner of the Aerosoft Beaver X and I also run Russel Dirk's FS Force for my Saitek FF Joystick. As part of the functionality of the FS Force program is that it "installs" a trim gauge in the 2D Panel. Unfortunately because the Beaver has no 2D panel I get a message each time I select the Beaver in FSX stating that the trim gauge is not installed on this plane. Is there a workaround for this and would it be possible to insert the gauge (accessed via the 1 and 7 numeric keys) in the VC? I am running FSX SP2 in WinXP Pro SP2, all other payware aircraft install the trim gauge without issue.

Thanks

PeterH

[Beaver X - POP up GPS]

Hi Guys

Many thanks for the responses, I have now discovered the updgrade and by switching between the VC and the zoomed GPS I can achieve the same effect.

Regards

PeterH

[Beaver X - POP up GPS]

HI

I have purchased the DHC Beaver for FSX and it works beautifully. I wanted to assign a "SHIFT + 2" key to allow me to have the GPS 295 to pop up to save me me zooming in on the inbuilt model each time to ensure I an on track. It works well but there is a black line at the base of the screen which sometimes flashes white-black and so on. Any ideas how I can get a pop up GPS 295 and not have this black line? I edited the panel.cfg file to achieve this effect.

I have attached a screenshot to show what I mean.

Thanks

PeterH