Aerosoft official retail partner for Microsoft Flight Simulator !! 
Click here for more information

Jump to content

egcc

Members
  • Content Count

    14
  • Joined

  • Last visited

Community Reputation

7 Neutral

About egcc

  • Rank
    Flight Student - Groundwork

Recent Profile Visitors

900 profile views
  1. I have this too. I find manually clicking on the relevant switch (it's often landing lights on vacating the runway) multiple times will eventually get the copilot to leave the switch alone and you can then manually set it to the correct position, at which point the checklist continues normally.
  2. Is there an action I need to perform for the FMA check in the descent checklist? I've found that with the copilot on, they will say "FMA check?" and then there's no response or action - pausing that checklist. Can't see anything in volume 5 of the documentation that might be relevant, so perhaps there are no further steps in this checklist?
  3. Hi Dave, Aware of the documentation and I know how my aircraft was configured (TA/RA and normal selected) but with an aircraft at the same level, crossing less than 5 miles ahead there was no warning when I would have expected there to be one...unless the TCAS doesn't warn in these situations, which is what I was asking about. I can't see anything in Volume 4 that talks about when you might or might not get an alert? Thanks Chris
  4. Earlier today I did a flight on Vatsim, using the FLAI modelset and Copilot as my client. Inbound to RESMI at FL350, with traffic crossing left to right 5 miles ahead - meaning I was 5 miles from RESMI as the other traffic was immediately over the waypoint. No TCAS alert of any type, though I'm not sure whether there should have been one? Are you able to share the expected normal behaviour so we can test on our various networks and setups?
  5. Version 1.0.2

    605 downloads

    Following on from my A320 file, here's the A321 one. Installation Navigate to %APPDATA%\Virtuali\Airplanes Create Aerosoft A320 CFM Professional if it doesn't already exist, otherwise open that folder Create gsx.cfg if it doesn't already exist, otherwise open that file in a text editor (Notepad++ recommended) Paste the code above in to that file, replacing anything already there Notes This GSX config will only use belt loaders, as I mainly fly European low cost and short haul and it's rare that they use the bins. Change BELT to AUTO in [cargo1] and [cargo2] if you'd like a mix, or to ULD if you'd just like the bins. No warranty is provided for this file, use it at your own risk and remember to take regular backups - especially if you're changing things!
  6. Sounds like the normal case of you not putting the weights in INIT B?
  7. I have those jagged lines on a repaint I installed that was for the legacy Airbus (32bit) so I wonder if it's a texture thing with old repaints?
  8. Version 1.0.1

    904 downloads

    A working version of gsx.cfg for Aerosoft A320 CFM Professional. Installation Navigate to %APPDATA%\Virtuali\Airplanes Create Aerosoft A320 CFM Professional if it doesn't already exist, otherwise open that folder Create gsx.cfg if it doesn't already exist, otherwise open that file in a text editor (Notepad++ recommended) Paste the code above in to that file, replacing anything already there Notes This GSX config will only use belt loaders, as I mainly fly European low cost and short haul and it's rare that they use the bins. Change BELT to AUTO in [cargo1] and [cargo2] if you'd like a mix, or to ULD if you'd just like the bins. No warranty is provided for this file, use it at your own risk and remember to take regular backups - especially if you're changing things!
  9. Agree with Tom. You're missing a lot of folders!
  10. Hi everyone, I was getting annoyed trying to get the cargo doors and messages to work correctly so I sat down and created my own profile for the CFM engined A320. You can of course use this for the other models too, though some tweaking may be needed. http://forum.aerosoft.com/index.php?/files/file/4871-gsxcfg-for-aerosoft-a320-cfm-professional/
  11. As xi-max said in your previous topic: "I would assume this livery was just converted over to the Professional from the original set of liveries."
  12. Just to note that this isn't just GSX v2, it's the same in v1. Constantly asking me to "open exit 2" or "close exit 2" once I eventually opened everything. Will play around with my GSX settings.
  13. RT @stuey_norris: Kimi out but having difficulty walking. Race has been red flagged

×
×
  • Create New...