birckdk 0 Posted June 13, 2016 Share Posted June 13, 2016 Hey there I have FSX, two computers, FSX on one, Prosim and all systems, among these AES remote, on the other. Works great. After a in house power failure, the IP addresses on the computers changed, eventually everything was configured again and working. HOWEVER..... I corrected the IP address in the VistaMare folder in FSX, and I corrected the IP address in the AES Remote window. All OK. BUT, When I shut down AES Remote, and start it up again, it comes up with a wrong IP address, even though I had pressed SAVE on the correct entry. It comes up with 192.168.1.1 while the correct one is, and was punched in: 192.168.1.24. It has been workng flawlessly for over a year!! Any ideas how I can correct this? regards P B Nielsen Copenhagen Link to comment Share on other sites More sharing options...
Developer OPabst 2091 Posted June 13, 2016 Developer Share Posted June 13, 2016 AESRemote will save the parameters into the Registry HKEY_LOCAL_MACHINE\SOFTWARE\Aerosoft\AES\AESRemote Maybe you can check, if this key changes, when you press the Save Button in the config menu. Link to comment Share on other sites More sharing options...
birckdk 0 Posted June 13, 2016 Author Share Posted June 13, 2016 Will do, and I'll get back to you with the result. Thanx!!! Link to comment Share on other sites More sharing options...
birckdk 0 Posted June 23, 2016 Author Share Posted June 23, 2016 Need some more help please: I have located the HKEY_LOCAL_MACHINE\SOFTWARE by typing regedit in the start menu, but there is no Aerosoft\AES\AESRemote. I have looked in both computers.....to no avail. Apparently I am missing something. Hope that you can help me out! Thanx. Link to comment Share on other sites More sharing options...
Developer OPabst 2091 Posted June 23, 2016 Developer Share Posted June 23, 2016 When you have a 64Bit Windows, check here: HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Aerosoft\AES\AESRemote Link to comment Share on other sites More sharing options...
birckdk 0 Posted June 23, 2016 Author Share Posted June 23, 2016 Thank you OPabst! We are closing in maybe, but I am taking small steps at a time here. Thank you for being patient. :-) The Aerosoft file was right where you said it would be, in the WOW folder.....now having locted this, I need guidance for the next step please. You say "Maybe you can check, if this key changes, when you press the Save Button in the config menu" I cannot see any changes when I press the save button in the " Setup AESRemote" window. And I do not know which config menu you are referring to unfortunately. And I wish I knew what to look for. Might it be easier to reset it, or am I almost there?? Regards P B Nielsen Copenhagen Link to comment Share on other sites More sharing options...
Developer OPabst 2091 Posted June 23, 2016 Developer Share Posted June 23, 2016 Yes, I mean the IP Botton in AESRemote, that the config menu for the IP Address. Have just test it, when I change the IP it is save and loaded correctly after restart of AESRemote. Did you try to start AESRemote "As Admin"? Maybe it is not save because of the UAC in normal mode. Link to comment Share on other sites More sharing options...
birckdk 0 Posted June 26, 2016 Author Share Posted June 26, 2016 Hello again. I Just checked, and AES Remote runs as administrator. The HKEY shows the correct IP address, however the AES Remote window comes up with the last digit missing every time and therefore the wrong IP address! I am stumped! Link to comment Share on other sites More sharing options...
Developer OPabst 2091 Posted June 27, 2016 Developer Share Posted June 27, 2016 Can you make a screenshot of the window showing the RegValue RemoteIP when you click on it. Link to comment Share on other sites More sharing options...
birckdk 0 Posted June 30, 2016 Author Share Posted June 30, 2016 Hello again Here are the relevant screen shots! Regards PBN Please login to display this image. Please login to display this image. Link to comment Share on other sites More sharing options...
birckdk 0 Posted August 11, 2016 Author Share Posted August 11, 2016 I solved it by punching in the correct IP address in the HKEY window.! All working well again! :-) Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.