Shack95

I‘m not 100% sure but that‘s how I remember it as well. I haven‘t had the time yet to thoroughly analyze it. The little time I had I used to enjoy flying the plane. My suspicion is that it had something to do with the autopilot. At some point I started to use the AP knob on the Bravo to set the V/S. It could be a coincidence but the problem began at roughly the same time. Another reason could be that I had two bindings for the flaps (buttons and axis). But that‘s just guessing. I‘ll post it here when I‘ve found it.

Yes!!! It finally works! I deleted all yoke and throttle mappings except for throttle, flaps, gear and roll/pitch. Now I'm going to re-map every button and axis I need one by one to find the culprit. It wasn't the trim (I'd already deleted that one). I'll report back when I've found it. This was really driving me crazy.

Thanks a lot for your recommendations. I‘ll try it as soon as I can and report back.

Yes, I have. I also watched The Dude‘s videos several times. I‘m new to the CRJ and I‘m what one might call an intermediate simmer, so it‘s absolutely possible that it‘s me doing something wrong. Since nobody seems to have the same problem it’s actually quite likely. The problem is, I can‘t see anything I‘m doing differently from what I‘ve read/watched in the tutorials. And the weird thing is, on my first few flights it worked. I also can’t think of anything I changed in my setup and I tried it with no other mods in the community folder.

Hello everyone, after a week of CRJ abstinence I tried it again today and I still can‘t get speed mode to work. I‘ve tried resetting and reinstalling the addon, deleting key bindings for the trim and speed brakes for my Honeycomb Alpha and Bravo, disengaging and reengaging AP and some other things. Nothing seems to work. The AP just refuses to adjust the pitch and the vertical FD bar doesn‘t move one bit. Other modes such as V/S, HDG and NAV seem to work as they should. Any help is greatly appreciated. I love this plane but I‘d love it even more if I could get this to work.

Thanks a lot for your input and the link. I've tried it with and without anti ice. Same result.

Yes, and only with speed mode. V/S mode works fine. Sometimes it stops at around 10000ft (when I‘m too slow) and sometimes I can easily climb up to FL250. The problem is that in speed mode the AP doesn’t seem to adjust the pitch, it just stays the same no matter what I do. I have. I also did a complete reinstallation of the plane. Someone in Avsim said there were some related files on the c:\ drive. I didn‘t delete those because I don‘t know which ones. I‘m wondering if it has something to do with the trim settings of my Honeycomb Bravo. Before my next flight I‘ll delete the bin

I normally fly with real weather, but I took the screenshots above with the clear sky preset because I didn't want to waste power on the anti ice system. I often don't enter a flex temperature because one of the youtube guys said it wouldn't be necessary. I thought without a flex temp you just use full power for takeoff. I sometimes used 47. Come to think about it, on my last flights I never entered one. Could that be the problem?

Thanks a lot for your explanations. I‘ve tried it several times in that order but the plane wouldn‘t climb once it reached its first set altitude. I also tried disengaging and re-engaging the AP, still nothing.

Another related issue I've encountered is that once I've reached my preselected altitude and want to climb to a higher altititude, speed mode doesn't seem to work either. It just won't climb. Instead I have to use V/S mode. Is that normal?

I tried disengaging and re-engaging several times. That didn't work. Yes, it's happened on every flight since a certain point. Before that, it worked fine.

Thank you for your reply. I use it for climbing and in the PFD it says “CLB” and my set speed (see attached image). I figured out how to avoid being too slow but speed mode still doesn’t seem to have any effect on the pitch. It’s not just 5 knots off but 10-20 or more.

On my last 10+ flights I couldn’t get speed mode to work properly, i.e. the AP never adjusts the pitch and I’m either to fast or too slow and the vertical flight director needle doesn’t move an inch. I followed the procedures described in the PDF tutorial and the Dude’s video tutorials and I can’t find anything I do differently. The weird thing is that it used to work and at some point it just stopped working (could have been after the update but I’m not sure). I’ve tried both resetting and reinstalling the plane, to no avail. I’m new to the CRJ and I’m not sure if it is me doing something wro