jimble 1 Posted February 23, 2013 Share Posted February 23, 2013 I have searched the forum but nobody else seems to have this problem...i can not get the cruise check lists to trigger, display shows cruise, second officer opens tray table etc. The cruise checklist is orange, i have tried pressing the check list button but no luck, it simply will not work. Any ideas as to why this might be.?. The airbus itself is superb, i have become addicted to my flight sim since i bought it...well done! Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted February 23, 2013 Deputy Sheriffs Share Posted February 23, 2013 Hi, I hope you are flying with a fully set up MCDU because this is one of the basics to use the checlist- and copilot functionality. The CRUISE CL should automatically start if you have reached the cruise altitude set in the MCDU and the FMA displays SPPED, ALT CRZ and NAV. "Orange" means active and to start it press the respective LSK next to it.........But the CRUISE CL should start automatically (no user interference) if the a. m. conditions are met....... Hanse Link to comment Share on other sites More sharing options...
jimble 1 Posted February 23, 2013 Author Share Posted February 23, 2013 Hello Hanse and thanks for your reply. I did think about the MCDU and did another flight late last night. I double checked everything so, if it's something that i am missing i don't know what it is. As i say, this is very strange as i am the only one having this problem I can trigger the before decent checklists by pressing the LSK button next to that check list. Regards. Link to comment Share on other sites More sharing options...
Domino 24 Posted February 23, 2013 Share Posted February 23, 2013 Hello Hanse and thanks for your reply. I did think about the MCDU and did another flight late last night. I double checked everything so, if it's something that i am missing i don't know what it is. As i say, this is very strange as i am the only one having this problem I can trigger the before decent checklists by pressing the LSK button next to that check list. Regards. Same here no cruise checklist. Michael (alias Domina :-)) V1.04 HotFix 011 Link to comment Share on other sites More sharing options...
rjord 86 Posted February 24, 2013 Share Posted February 24, 2013 jimble When you are ready to press the before descend checklist has this checklist turned orange or it that still stuck on cruise. Once I reach the cruise level and the tray table is out, the only time I go back to the checklist is when I am preparing to descend and at this time the prepare to decend checklist has turned orange. Roy Link to comment Share on other sites More sharing options...
jimble 1 Posted February 24, 2013 Author Share Posted February 24, 2013 Hi Roy, The cruise checklist does not play at all. The decent checklists begins without any problem. Thaks. Link to comment Share on other sites More sharing options...
edgehead 2 Posted February 24, 2013 Share Posted February 24, 2013 Same problem here. I thought there was no cruise checklist at all. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted February 24, 2013 Deputy Sheriffs Share Posted February 24, 2013 Hi Guys, let us first clear what CRUISE CL means (details you will find in Vol6 StepbyStep Guide chapter 5.16). Part of this cecklist are only three items:TCAS TA or TA/RA plus TILT NORMAL = SETSEAT BELTS = OFFSLIDING TABLE COPILOT = EXTENDED So the question is are those actions performed if the Copilot is set to ON? Or did you manually do it? Then this checklist stays active until the next DESCENT PREPARATION CL starts..... Hanse Link to comment Share on other sites More sharing options...
Kurt2404 3 Posted February 24, 2013 Share Posted February 24, 2013 TCAS TA or TA/RA plus TILT NORMAL = SETSEAT BELTS = OFFSLIDING TABLE COPILOT = EXTENDED Hi Hanse, checked this out today: RADAR TILT NORMAL is called during AFTER-TAKE OFF-CL but not later (no CRUISE-CL at all) SEAT BELTS OFF is neither called nor executed regardless the COPILOT status SLIDING TABLE COPILOT EXTENDED just takes place when COPILOT is ON, else no extension SLIDING TABLE STOWED is also just executed during APPRCH-CL when COPLIOT is ON I am using Win7 64bit home premium, FSX-Gold + SP1 + Acc.-Pack, AXE 1.04 + all HFs Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted February 24, 2013 Deputy Sheriffs Share Posted February 24, 2013 Hi Kurt, you are writing AXE 1.04 and all Hotfixes...... Relevant for 1.04 is only HF 011 (012 is just the new fuelplanner). This means you should have newly installed release 1.04 and on top of that HF 011. And thats it. I also think that you are flying with a fully set up MCDU. So after reaching the cruise level what does the FMA on the PFD show? it should be SPPED, ALT CRZ and NAV! Please check..... Hanse Link to comment Share on other sites More sharing options...
jimble 1 Posted February 25, 2013 Author Share Posted February 25, 2013 Sorry to but in gentlemen, I can confirm SPEED, ALT CRZ and NAV, second officer's tray extended, cruise CL green..I think, but not sure, that the cruise check list is garbled with the descent CL (both playing at the same time) . 1.04 with hotfix 011. Thanks for your continued help with this. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted February 25, 2013 Deputy Sheriffs Share Posted February 25, 2013 Sorry to but in gentlemen, I can confirm SPEED, ALT CRZ and NAV, second officer's tray extended, cruise CL green..I think, but not sure, that the cruise check list is garbled with the descent CL (both playing at the same time) . 1.04 with hotfix 011. Thanks for your continued help with this. If the copilots tray is extended it means that the CRUISE CL has been finished. The next CL i. e. the DESCENT CL starts automatically 8 NM before TOD or if you start to change the altitude...... So what do you mean by "both playing at the same time"? Hanse Link to comment Share on other sites More sharing options...
Kurt2404 3 Posted February 25, 2013 Share Posted February 25, 2013 I also think that you are flying with a fully set up MCDU. So after reaching the cruise level what does the FMA on the PFD show? it should be SPPED, ALT CRZ and NAV! Please check..... Hi Hanse, yes Sir, I confirm that MCDU was configured properly (the complete flight from LOWW to ESSA was performed without any problems beside the described CL-issue). Also SPEED, ALT CRZ and NAV were lit during the cruise phase and the DESCEND PREPARATION CL worked fine as well. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted February 25, 2013 Deputy Sheriffs Share Posted February 25, 2013 Hi Hanse, yes Sir, I confirm that MCDU was configured properly (the complete flight from LOWW to ESSA was performed without any problems beside the described CL-issue). Also SPEED, ALT CRZ and NAV were lit during the cruise phase and the DESCEND PREPARATION CL worked fine as well. Hi Kurt, as already explained the CRUISE CL contains just 3 actions:TCAS TA or TA/RA plus TILT NORMAL = SETSEAT BELTS = OFFSLIDING TABLE COPILOT = EXTENDED So please have a look into to CHECKLIST Menu on the right MCDU (LSK1R) and then go to the second page (using the button with the arrow showing to the right) which CL is active = green. After the above actions are performed the CRUISE CL should be green and the DESCENT PREP CL = orange. After the DESCENT PREP CL has been finished all CL are grey until the DESCENT has been started...... This is how it works perfectly on my system. Regards, Hanse Link to comment Share on other sites More sharing options...
Kurt2404 3 Posted February 25, 2013 Share Posted February 25, 2013 So please have a look into to CHECKLIST Menu on the right MCDU (LSK1R) and then go to the second page (using the button with the arrow showing to the right) which CL is active = green. After the above actions are performed the CRUISE CL should be green and the DESCENT PREP CL = orange. After the DESCENT PREP CL has been finished all CL are grey until the DESCENT has been started...... This is how it works perfectly on my system. Hi Hanse, you see me embarrassed - I did not even realize that there is a second CL-page on the MDCU. It seems that I should have RTFM even more carefully. Thanks for your perfect help (as always) and wish you all the best for the upcoming update to 1.05! Link to comment Share on other sites More sharing options...
jimble 1 Posted February 25, 2013 Author Share Posted February 25, 2013 If the copilots tray is extended it means that the CRUISE CL has been finished. The next CL i. e. the DESCENT CL starts automatically 8 NM before TOD or if you start to change the altitude...... So what do you mean by "both playing at the same time"? Hanse Hi Hanse. I think that the cruise CL might be mixed in with the descent CL's when they start. Kurt says that he didn't realize that there was a second MCDU page but wouldn,t the cruise CL's still have started automatically? Link to comment Share on other sites More sharing options...
Kurt2404 3 Posted February 25, 2013 Share Posted February 25, 2013 Hi Hanse coming back to the problem once more, I may send the following pictures of my today's flight from EDDN to LOWW: Climb phase: Please mind: CRUISE CL is not orange! Cruise phase: Please mind: CRUISE is active, but the table is still retracted due to copilot not being active. When activated the sliding table is extended. No CRUISE-CL is performed in both cases! Descend preparation phase: As you may see the DESCEND PREPARATION is normally performed and active. This complete behaviour is fully acceptable for me because all really important CL-items are handled in the AFTER TO-CL and DESCEND PREP-CL anyway. The complete managed descend and the following ILS-APPCH to RWY34 including all speed and altitude constraints were performed by the AC in a perfect manner. No problems with DCT-TO and CLs at all. Link to comment Share on other sites More sharing options...
jimble 1 Posted February 25, 2013 Author Share Posted February 25, 2013 Hi Hanse coming back to the problem once more, I may send the following pictures from my today's flight from EDDN to LOWW: Climb phase: Please mind: CRUISE CL is not orange! Cruise phase: Please mind: CRUISE is active, but the table is still retracted due to copilot not being active. When activated the sliding table is extended. No CRUISE-CL is performed in both cases! Descend preparation phase: As you may see the DESCEND PREPARATION is normally performed and active. This complete behaviour is fully acceptable for me because all really important CL-items are handled in the AFTER TO-CL and DESCEND PREP-CL anyway. The complete managed descend and the following ILS-APPCH to RWY34 including all speed and altitude constraints was performed by the AC in a perfect manner. No problems with DCT-TO and CLs at all. Agreed. It doesn't effect the functionality of the Aircraft. Still very happy with my purchase. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted February 26, 2013 Deputy Sheriffs Share Posted February 26, 2013 Hi Kurt, sorry but I am completely confused........ What is the real problem with your CRUISE CL. As I already told you there are only three items happening during this checklist:TCAS TA or TA/RA plus TILT NORMAL = SETSEAT BELTS = OFFSLIDING TABLE COPILOT = EXTENDED Looking into your picture the seat belt signs are off and you are confirming that if the copilot is set to ON then the sliding table is extended. So is there a problem with the TCAS setting? Hanse Link to comment Share on other sites More sharing options...
Kurt2404 3 Posted February 27, 2013 Share Posted February 27, 2013 So is there a problem with the TCAS setting? Hi Hanse, sorry for being maybe not explicitly enough... No, there is also no problem with TCAS/RADAR TILT = NORMAL because this is already checked and managed during the AFTER TAKE OFF CL. The only issue is simply that the CRUISE CL is not performed as the other checklists which always start with a call like "AFTER TAKE OFF CHECKLIST" followed by all the items to be checked and finalized with "CL COMPLETE". This is not the case for the CRUISE CL - no calls at all altough the functionality behind is working correct. As mentioned before this is not a problem for flying at all but if somebody expects the initation of an audible cruise checklist he/she will not be successful. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted February 27, 2013 Deputy Sheriffs Share Posted February 27, 2013 Hi Kurt, OK now I know the point: We will have a look into it....... Hanse Link to comment Share on other sites More sharing options...
Slayer 2 Posted March 3, 2013 Share Posted March 3, 2013 Maybe it is that the cruise is a flow rather than a checklist that is why it is not being explicitly stated? Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted March 7, 2013 Deputy Sheriffs Share Posted March 7, 2013 Hi, we checked the issue and confirm "Slayers" opinion that this is just a flow and not a complete checklist. Therefore there are no calls from PnF and PF. I will also add a short explanation to the Vol6 StepbyStep Guide....... Hanse Link to comment Share on other sites More sharing options...
Kurt2404 3 Posted March 8, 2013 Share Posted March 8, 2013 I will also add a short explanation to the Vol6 StepbyStep Guide....... Perfect - thanks a lot! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.