Recently we have seen a lot of codes used to unlock our products being offered for discounted prices. Almost all of them are bought using stolen credit cards. These codes will all be blocked by our systems and you will have to try to get your money back from the seller, we are unable to assist in these matters. Do be very careful when you see a deal that is almost too good to be true, it probably is too good to be true.

Jump to content
Sign in to follow this  
PW2000

Munich X Runway Light

Recommended Posts

Hello,

I just installed Munich X and did some flights from and to Munich X. And I discovered the following problem, when I set visibility to 1,2 km (or less) the runway lights

are not working during daytime. I checked it with the same weather settings in Frankfurt and Hanover (both Aerosoft sceneries) and the runway lights are on.

So it must be a bug of Munich X. (Weather was no clouds, light wind and up to FL 95 visibility 1.2 km)

Does some else have this problem, and how can it be fixed ?

(I use only FSX weather, no real world weather).

And one more thing is the tower view point. In my version it is a very high point above the real tower (same bug as with Paderborn X Scenery ?). So you have a good view

over the complete Airport, but thats not the real tower view I think.

Markus

Share this post


Link to post

Did you see the cars of AESlite driving around?

Do you have a VistaMare subdirectory below ADD-Ons

Share this post


Link to post

I see no cars driving (I think I deactivated them with the traffic tool of Munich X to increase frame rate)

And I have to check for VistaMare subdirectory but I think no.

Markus

Share this post


Link to post

It's not a Subdir, it's a Submenü below the FSX Menu entry Add-Ons. If this is missing, there is no controll about the Lights, so no lights at daytime at all.

Which FSX Version you have ACC-Pack or SP2? If non of both, the Modules will not work, so you need to install SP2 or ACC-Pack.

If you one of this, try to reinstall the Scenery with the newest Installer.

Share this post


Link to post

I have FSX with ACC-Pack, but no VistaMare Module, Subdirectory or Sub folder.

I will try to reistall it, but ACC-Pack I had also installed during the first installation of Munich X,

so I don´t expect any changes there, but I will try it this evening.

Thank you the fast answers. Markus

(I have also no cars (or Trains) when I activate them with the Munich X Traffic Control Tool, only standard FSX Airport Traffic when on).

Share this post


Link to post

Ok, I could fix it on my own.

I reinstalled Munich X, started it, again no traffic, no runway lights.

I searched for VistaMare folder, found it under FSX Main Folder.

Than I opened dll file under AppData/Roamin/Microsoft/FSX and found the file ViMaCoreX.dll disabled, I activated it and now everythink works (Cars, Trains and Runway Lights).

Maybe its a mistake in the installation routine.

But with the runway Lights working during low visibility (1.2km), I found one small thing, during approach the PAPI Lights (2 red and 2 white) are visible in the fog, long

before I can see the first runway lights ! Check it, only a small mistake.

Great scenery, outstanding, with good frame rate even with traffic, but next time please a release without bugs! For me the most time working with FSX is to fix bugs,

and not flying! Thats your job during testing just BEFORE release !

I hope than for a small update to fix the wrong elevation of the Tower View Point !

Now you can close this Topic as solved.

Thank you for your good support. See you with the next bug.

Markus

Share this post


Link to post

Great scenery, outstanding, with good frame rate even with traffic, but next time please a release without bugs! For me the most time working with FSX is to fix bugs,

and not flying! Thats your job during testing just BEFORE release !

Fine, that it works, but the only issue you had was the Disabled Call in the DLL.XML and we are 100% sure, that this will not be generated by the Installer. If you had this entry before, it is not overwritten, so maybe you have set it to Disable="True" long before. So no bug, maybe an issue on you installation.

Share this post


Link to post
Guest
This topic is now closed to further replies.
Sign in to follow this  

×
×
  • Create New...