Poltergeist 0 Posted March 17, 2021 Share Posted March 17, 2021 Hello, the aircraft has been flawless for the most part. However, I've found that my throttle is very weird with how it sets thrust. I mostly notice this on final when I'm dialing in VREF, but I've also noticed this in cruise as well. The thrust seems to jump all over the place. For example, If I'm coming in just a little slow and add some thrust to compensate, the engines will spool down first, then aggressively spool up to whatever new value I set. It's been making doing smooth approaches impossible. If needed I can post a video of the phenomenon. It happens most often when near the CLIMB detent. I make sure to never move into the detent, but just being nearby it causes these throttle issues. I've calibrated my throttle a few times to see if thats the issue, but the problems persist. Link to comment Share on other sites More sharing options...
Aerosoft SimWare 730 Posted March 17, 2021 Aerosoft Share Posted March 17, 2021 Dear Sir, Do you see the throttle in the aicraft move erratically too ? Or is it only the aircraft itself ? Link to comment Share on other sites More sharing options...
BabyPeel 3 Posted March 18, 2021 Share Posted March 18, 2021 Hi. Yes this issue is apparently true for ALL T16000M throttles currently (advancing throttle causes N1 and N2 to drop by a few percent, before increasing overall. Resulting in a loss of power for about 2 seconds each time the throttle is advanced forward). Hopefully this issue will be fixed soon. Link to comment Share on other sites More sharing options...
Aerosoft SimWare 730 Posted March 18, 2021 Aerosoft Share Posted March 18, 2021 Dear Sir, This isn't a CRJ issue as the throttles, T16000 or other, all are a simple analog axis. the CRJ only reads the axis values, whatever the throttle type is. Please first check the calibration in Windows : Please login to display this image. Then pelase refer to the thottle calibration documentation attached. Best regards. CRJ Throttle Calibration Manual.pdf Link to comment Share on other sites More sharing options...
BabyPeel 3 Posted March 18, 2021 Share Posted March 18, 2021 12 minutes ago, SimWare said: Dear Sir, This isn't a CRJ issue as the throttles, T16000 or other, all are a simple analog axis. the CRJ only reads the axis values, whatever the throttle type is. Please first check the calibration in Windows : Please login to display this image. Then pelase refer to the thottle calibration documentation attached. Best regards. CRJ Throttle Calibration Manual.pdf 2.36 MB · 0 downloads I'm afraid you're wrong. The axis is fine. The virtual throttle in the cockpit moves perfectly in sync with everyone's real throttle. The N1 and N2 is what's acting up. Link to comment Share on other sites More sharing options...
Meowfly 20 Posted March 18, 2021 Share Posted March 18, 2021 I have this same problem with the Warthog throttle. And funny enough, it also happens with the CRJ in P3D. No other plane I own in any sim has this issue. Link to comment Share on other sites More sharing options...
Philipp Wichert 1 Posted March 18, 2021 Share Posted March 18, 2021 Hi, have experienced the same issue- and worked through all solution ( suggestions...) I could find on the Inet. Halfway glad that this is a known issue and will hopefully be adressed by some patch in future- halfway dissapointed of course. Funny that the simple thrust lever directly on the joystick works smooth like butter- its only the throttle quadrant of the T1600M that causes trouble. Okay will wait then until patch comes out. Cheers Philipp Link to comment Share on other sites More sharing options...
Halvie 0 Posted March 18, 2021 Share Posted March 18, 2021 I’m experiencing the same issue with a Honeycomb Bravo. Everything is calibrated appropriately both in Windows and through the EFB. Something is definitely up with the CRJ. Link to comment Share on other sites More sharing options...
Michal Szkodzinski 2 Posted March 18, 2021 Share Posted March 18, 2021 Same problem with x56 throttle Link to comment Share on other sites More sharing options...
Aerosoft SimWare 730 Posted March 19, 2021 Aerosoft Share Posted March 19, 2021 - To what function is the throttle axis assigned ? - What is the sensitivity curve of the axis in MSFS. It should be linear. I suppose the throttle calibration procedure (attached) was followed ? CRJ Throttle Calibration Manual.pdf Link to comment Share on other sites More sharing options...
Philipp Wichert 1 Posted March 19, 2021 Share Posted March 19, 2021 vor 7 Minuten, SimWare sagte: - To what function is the throttle axis assigned ? - What is the sensitivity curve of the axis in MSFS. It should be linear. I suppose the throttle calibration procedure (attached) was followed ? CRJ Throttle Calibration Manual.pdf 2 MB · 0 downloads Yep - for my part I have tried everything ( even the hint assigning the Throttle to Axis 1 and Axis 2 in the MSFS Menue) . Interesting however is that the lever directly on the Joystich itself ( T1600 M) works flawless. Same is with the XBox Controller- smooth as butter. Well - so the cookie crumbles- just have to wait... I am more than happy with the rest !!!! Cheers Link to comment Share on other sites More sharing options...
Michal Szkodzinski 2 Posted March 19, 2021 Share Posted March 19, 2021 1 hour ago, SimWare said: - To what function is the throttle axis assigned ? - What is the sensitivity curve of the axis in MSFS. It should be linear. I suppose the throttle calibration procedure (attached) was followed ? CRJ Throttle Calibration Manual.pdf 2.36 MB · 0 downloads Yes, it is linear and yes it was followed Link to comment Share on other sites More sharing options...
Michal Szkodzinski 2 Posted March 19, 2021 Share Posted March 19, 2021 Look on N1 when i move throttle down Please login to display this image. Please login to display this image. Please login to display this image. Please login to view this video. Link to comment Share on other sites More sharing options...
Michal Szkodzinski 2 Posted March 19, 2021 Share Posted March 19, 2021 And here...... Please login to view this video. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.