Jump to content

How to use the TCA throttle, the reverse levers and Starter buttons with Aerosoft Aibusses under P3Dv4/v5


SimWare
 Share

Recommended Posts

I really apologize for not answering. The answer to my question in the forum was quick and satisfied.
I had a lot of troubles with the TCM captains pack  , I even had to return them to France . TCM did this well in guarantee . Get the captain's pack back I struggled with the power levers ( no idle , no reverse and climb and flex setting ) searching in the TCM software and p3d4 , I found out do some reasons < I don`t know< in p3d4 , raw input was engaged , I changed it to direct input and it all works.  Thanks for answering and help.
the video help great I use the black button(17) left from trim knob to  rest the trim , as in the airbus.
a happy airbus an tcm user
  • Thanks 1
Link to comment
Share on other sites

On 9/11/2021 at 1:46 PM, AlexAnt said:

I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL.  Very frustrating.   Thanks for recommendation, i'll try FSLabs in case of no solution in few days.

HI, Try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi

  • Like 1
Link to comment
Share on other sites

On 9/11/2021 at 1:46 PM, AlexAnt said:

I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL.  Very frustrating.   Thanks for recommendation, i'll try FSLabs in case of no solution in few days.

Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi

Link to comment
Share on other sites

On 9/11/2021 at 1:46 PM, AlexAnt said:

I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL.  Very frustrating.   Thanks for recommendation, i'll try FSLabs in case of no solution in few days.

Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi

Link to comment
Share on other sites

On 9/11/2021 at 1:46 PM, AlexAnt said:

I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL.  Very frustrating.   Thanks for recommendation, i'll try FSLabs in case of no solution in few days.

Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi

Link to comment
Share on other sites

On 9/11/2021 at 1:46 PM, AlexAnt said:

I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL.  Very frustrating.   Thanks for recommendation, i'll try FSLabs in case of no solution in few days.

Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi

Link to comment
Share on other sites

3 hours ago, mousemansteven said:

which procedure did you use there are several regards Steve

What I did is just simply go to P3D settings - options - calibration - calibrate device. Move the two throttles down to full reverse and push them all the way to MAN TOGA. Then pull them back to CL position, which is at the center of the white bar, and also just around the center of the range (in fact the raw value at CL is about 32500-33000/65535, and the perfect center should be 32768). Leave it CL and click "Save", and that's it.

  • Like 1
Link to comment
Share on other sites

On 11/4/2021 at 2:27 PM, SimWare said:

Hi Steve,

 

You can use this one :

 

 

afternoon my friend. i have been at it finally after reinstalling everything i decided to  check the a3xx configurator. i had previously had all three items ticked where  it offers the tca support. i removed the sidestick support and low and behold it actually worked. for some reason though the mapping for the spoilers is not working. again thanks for your dedication, regards Steve

Link to comment
Share on other sites

  • Aerosoft
2 hours ago, mousemansteven said:

afternoon my friend. i have been at it finally after reinstalling everything i decided to  check the a3xx configurator. i had previously had all three items ticked where  it offers the tca support. i removed the sidestick support and low and behold it actually worked. for some reason though the mapping for the spoilers is not working. again thanks for your dedication, regards Steve

Hi Steve,

 

Glad it works. 

How are the spoilers mapped in the simulator? 

 

Thank you.

Link to comment
Share on other sites

  • Aerosoft
47 minutes ago, mousemansteven said:

rz axis  but when i try to change it will not see the spoiler axis when the arm is moved regards

 

Thank you Steve.

 

Actually my question is : To what function is the axis assigned in the simulator ?
You can send me a screenshot of the assignments panel.

 

Best regards.

Link to comment
Share on other sites

5 hours ago, SimWare said:

 

Thank you Steve.

 

Actually my question is : To what function is the axis assigned in the simulator ?
You can send me a screenshot of the assignments panel.

 

Best regards.

the rz axis is assigned to the spoiler axis  in add on 1 and 2  not the throttle is that what you mean

Link to comment
Share on other sites

1 hour ago, mousemansteven said:

the rz axis is assigned to the spoiler axis  in add on 1 and 2  not the throttle is that what you mean

also when i try to change the spoiler axis  ( RZ) in p3d it wont change regards, btw in my haste i had reinstalled p3d aerosoft a330 in the wrong folder so therefor no websimbrowser. i reinstalled to the main p3dv5 folder and now efb is functional.

Link to comment
Share on other sites

  • Aerosoft
11 hours ago, mousemansteven said:

Thanks C. i deleted the config  and when i reopened p3d it worked wow so now i can fly yeah.. thanks for your help and dedication to the sim world. warm regards Steve the old fart

You are welcome, Steve.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...