wildeboer 3 Posted October 23, 2021 Share Posted October 23, 2021 I really apologize for not answering. The answer to my question in the forum was quick and satisfied. I had a lot of troubles with the TCM captains pack , I even had to return them to France . TCM did this well in guarantee . Get the captain's pack back I struggled with the power levers ( no idle , no reverse and climb and flex setting ) searching in the TCM software and p3d4 , I found out do some reasons < I don`t know< in p3d4 , raw input was engaged , I changed it to direct input and it all works. Thanks for answering and help. the video help great I use the black button(17) left from trim knob to rest the trim , as in the airbus. a happy airbus an tcm user 1 Link to comment Share on other sites More sharing options...
Aerosoft SimWare 729 Posted October 23, 2021 Author Aerosoft Share Posted October 23, 2021 Hi WildeBoer, No problem at all. Happy it is now working. Have fun flights ! 1 Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted October 30, 2021 Share Posted October 30, 2021 hi SimWare. i am still having detent issues. in the a330 and a318 to a321 in order to get to idle i have to lift the reverse levers and pull all the way down weird ill keep on trying at least i can fly regards, Steve Link to comment Share on other sites More sharing options...
Aerosoft SimWare 729 Posted October 31, 2021 Author Aerosoft Share Posted October 31, 2021 Hi Steve, To understand exactly the behavior, can you please make a short video showing the TCA and the throttle response in the simulator ? Thank you. Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted November 1, 2021 Share Posted November 1, 2021 Please login to view this video. ok i tried my best thank you C. for your patience Link to comment Share on other sites More sharing options...
叶奕奕 3 Posted November 4, 2021 Share Posted November 4, 2021 On 9/11/2021 at 1:46 PM, AlexAnt said: I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL. Very frustrating. Thanks for recommendation, i'll try FSLabs in case of no solution in few days. HI, Try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi 1 Link to comment Share on other sites More sharing options...
叶奕奕 3 Posted November 4, 2021 Share Posted November 4, 2021 On 9/11/2021 at 1:46 PM, AlexAnt said: I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL. Very frustrating. Thanks for recommendation, i'll try FSLabs in case of no solution in few days. Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi Link to comment Share on other sites More sharing options...
叶奕奕 3 Posted November 4, 2021 Share Posted November 4, 2021 On 9/11/2021 at 1:46 PM, AlexAnt said: I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL. Very frustrating. Thanks for recommendation, i'll try FSLabs in case of no solution in few days. Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi Link to comment Share on other sites More sharing options...
叶奕奕 3 Posted November 4, 2021 Share Posted November 4, 2021 On 9/11/2021 at 1:46 PM, AlexAnt said: I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL. Very frustrating. Thanks for recommendation, i'll try FSLabs in case of no solution in few days. Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi Link to comment Share on other sites More sharing options...
叶奕奕 3 Posted November 4, 2021 Share Posted November 4, 2021 On 9/11/2021 at 1:46 PM, AlexAnt said: I have similar situation - i have reverse, CL, FLEX and TOGA, but nothing more - when i put thrust to idle, in the aircraft it's positioned to CL. Very frustrating. Thanks for recommendation, i'll try FSLabs in case of no solution in few days. Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi Link to comment Share on other sites More sharing options...
叶奕奕 3 Posted November 4, 2021 Share Posted November 4, 2021 Oh damn my network lagged and I didn't know that I sent the same thing several times! Apologies for that... 1 Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted November 4, 2021 Share Posted November 4, 2021 1 hour ago, 叶奕奕 said: Hi, try again calibrate your thrust axis, but remember to leave it at CL before clicking "finish", as the calibration page says "leave all axis on center before finishing". LG Yeyi which procedure did you use there are several regards Steve Link to comment Share on other sites More sharing options...
Aerosoft SimWare 729 Posted November 4, 2021 Author Aerosoft Share Posted November 4, 2021 Hi Steve, You can use this one : Link to comment Share on other sites More sharing options...
叶奕奕 3 Posted November 4, 2021 Share Posted November 4, 2021 3 hours ago, mousemansteven said: which procedure did you use there are several regards Steve What I did is just simply go to P3D settings - options - calibration - calibrate device. Move the two throttles down to full reverse and push them all the way to MAN TOGA. Then pull them back to CL position, which is at the center of the white bar, and also just around the center of the range (in fact the raw value at CL is about 32500-33000/65535, and the perfect center should be 32768). Leave it CL and click "Save", and that's it. 1 Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted November 7, 2021 Share Posted November 7, 2021 On 11/4/2021 at 2:27 PM, SimWare said: Hi Steve, You can use this one : afternoon my friend. i have been at it finally after reinstalling everything i decided to check the a3xx configurator. i had previously had all three items ticked where it offers the tca support. i removed the sidestick support and low and behold it actually worked. for some reason though the mapping for the spoilers is not working. again thanks for your dedication, regards Steve Link to comment Share on other sites More sharing options...
Aerosoft SimWare 729 Posted November 7, 2021 Author Aerosoft Share Posted November 7, 2021 2 hours ago, mousemansteven said: afternoon my friend. i have been at it finally after reinstalling everything i decided to check the a3xx configurator. i had previously had all three items ticked where it offers the tca support. i removed the sidestick support and low and behold it actually worked. for some reason though the mapping for the spoilers is not working. again thanks for your dedication, regards Steve Hi Steve, Glad it works. How are the spoilers mapped in the simulator? Thank you. Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted November 8, 2021 Share Posted November 8, 2021 15 hours ago, SimWare said: Hi Steve, Glad it works. How are the spoilers mapped in the simulator? Thank you. rz axis but when i try to change it will not see the spoiler axis when the arm is moved regards Link to comment Share on other sites More sharing options...
Aerosoft SimWare 729 Posted November 8, 2021 Author Aerosoft Share Posted November 8, 2021 47 minutes ago, mousemansteven said: rz axis but when i try to change it will not see the spoiler axis when the arm is moved regards Thank you Steve. Actually my question is : To what function is the axis assigned in the simulator ? You can send me a screenshot of the assignments panel. Best regards. Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted November 8, 2021 Share Posted November 8, 2021 5 hours ago, SimWare said: Thank you Steve. Actually my question is : To what function is the axis assigned in the simulator ? You can send me a screenshot of the assignments panel. Best regards. the rz axis is assigned to the spoiler axis in add on 1 and 2 not the throttle is that what you mean Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted November 8, 2021 Share Posted November 8, 2021 18 minutes ago, mousemansteven said: the rz axis is assigned to the spoiler axis in add on 1 and 2 not the throttle is that what you mean Please login to display this image. Please login to display this image. Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted November 8, 2021 Share Posted November 8, 2021 1 hour ago, mousemansteven said: the rz axis is assigned to the spoiler axis in add on 1 and 2 not the throttle is that what you mean also when i try to change the spoiler axis ( RZ) in p3d it wont change regards, btw in my haste i had reinstalled p3d aerosoft a330 in the wrong folder so therefor no websimbrowser. i reinstalled to the main p3dv5 folder and now efb is functional. Link to comment Share on other sites More sharing options...
Aerosoft SimWare 729 Posted November 15, 2021 Author Aerosoft Share Posted November 15, 2021 Hello Steve, Assigning the lever to the Spoiler axis in P3D works. (see the video hereunder) Please make sure no other assignments to any spoiler function exists anywhere (even on other connected devices) 1 Link to comment Share on other sites More sharing options...
mousemansteven 27 Posted November 16, 2021 Share Posted November 16, 2021 Thanks C. i deleted the config and when i reopened p3d it worked wow so now i can fly yeah.. thanks for your help and dedication to the sim world. warm regards Steve the old fart Link to comment Share on other sites More sharing options...
Aerosoft SimWare 729 Posted November 17, 2021 Author Aerosoft Share Posted November 17, 2021 11 hours ago, mousemansteven said: Thanks C. i deleted the config and when i reopened p3d it worked wow so now i can fly yeah.. thanks for your help and dedication to the sim world. warm regards Steve the old fart You are welcome, Steve. Link to comment Share on other sites More sharing options...
Cloudchaser 0 Posted February 12, 2022 Share Posted February 12, 2022 Does this method also work with the Aerosoft A330? Been having issues with it for a long time, as well as calibration issues with the throttle levers and everything on the throttle add-on quadrant not working (spoilers and flaps do work, however they are reversed and skip a detent or two). My hardware completely fine FYI. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now