Jov 5 Posted August 10, 2018 Share Posted August 10, 2018 I have a clear reproducable error. The CL reaches "Pitch Trim" an I set the trim as calculated in the Fuel planner and also shown in the "Perf" page. However, I don't get a "set" call" so I have to skip the item. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted August 10, 2018 Deputy Sheriffs Share Posted August 10, 2018 Please get me the value you are working with e.g. the one displayed in the MCDU 3 after INIT LOADSHEET as well as the one in the MCDU 1 PERF page - (obviously both values should be the same...) Then I will try to reproduce...... Regards, Rolf Link to comment Share on other sites More sharing options...
Jov 5 Posted August 12, 2018 Author Share Posted August 12, 2018 sorry I reposted the issue, because I could not find my post again ;o) I just did this flight (attachment) When the checklist comes to the point "pitch trim" I turn the wheel until I get "up 0,5 on the ECAM. There is no "set" call. I tried to move the wheel some more and back below the setting, No call. Please login to display this image. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted August 12, 2018 Deputy Sheriffs Share Posted August 12, 2018 The set pitch trim is checked with the value in the MCDU PERF TAKEOFF page (next to the flaps setting). Standard is UP0.8. But if you use "Generate Loadsheet" and in the MCDU 3 LOAD FUEL page as well INIT then the UP0.5 from the Fuel Planner is imported into the Airbus..... Then also automatically the MCDU PERF TAKEOFF page is updated with UP0.5........ Regards, Rolf Link to comment Share on other sites More sharing options...
Hoffie3000 96 Posted August 12, 2018 Share Posted August 12, 2018 Rolf, the Problem is that you have to use the Generate Loadsheet. Some People like to enter required Data by hand. But in MCDU3 you cant change trim value manual and that cause that the Checkliste stuck if you have trim Data other as 0.8 Gruß, Wolfgang Link to comment Share on other sites More sharing options...
Jov 5 Posted August 12, 2018 Author Share Posted August 12, 2018 Well I did not do that. I used the loadsheet and have attached the stepts that I took. As you see, the values from the fuelplanner were correctly passed on to the loadsheet in the 2nd MCDU and subsequently into the TO Perf page. I got no call "set" @ pitch trim up 0,3. So I played with the wheel, tried up 0,8 (default), got no call. turned down to 0,3, no call. Then, at up 0,2 I suddenly got a call. Please login to display this image. Please login to display this image. Please login to display this image. Please login to display this image. Please login to display this image. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted August 12, 2018 Deputy Sheriffs Share Posted August 12, 2018 vor 1 hour , Hoffie3000 sagte: But in MCDU3 you cant change trim value manual and that cause that the Checkliste stuck if you have trim Data other as 0.8 Wolfgang, that is not correct. Try to enter in the MCDU p.e. 1/UP0.3 and it should work......... Regards, Rolf Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted August 13, 2018 Deputy Sheriffs Share Posted August 13, 2018 Jov, your are right e. g. there is a problem if you manually set "pitch trim". The reason seem to be that the "tolerances" we currently use are too small....... If you slowly use the trim wheel (click after click) with the mouse wheel through all the possible trim wheel settings for p. e. UP0.3 then you will find the right position..... for the CL to accept the setting. We have a look into this and try to find a solution. Regards, Rolf Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted August 14, 2018 Deputy Sheriffs Share Posted August 14, 2018 Solution will be included in the next hotfix / update...... Regards, Rolf Link to comment Share on other sites More sharing options...
Deputy Sheriffs Hanse 216 Posted August 17, 2018 Deputy Sheriffs Share Posted August 17, 2018 Because we believe this topic has been answered we have closed it. If you have any more questions feel free to open a new topic. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.