Recently we have seen a lot of codes used to unlock our products being offered for discounted prices. Almost all of them are bought using stolen credit cards. These codes will all be blocked by our systems and you will have to try to get your money back from the seller, we are unable to assist in these matters. Do be very careful when you see a deal that is almost too good to be true, it probably is too good to be true.

Jump to content
Sign in to follow this  
Christian85

DHC6 Twin Otter Extended (VC)

Recommended Posts

Dear Aerosoft Team

 

cant understand why is the Yoke movement not fully 90°degrees in the Twin Otter (Virtual Cockpit)   look on the new AN-2 or Default Cessna 172 /Maule etc ! 

 

 

Thank you

 

best regards

 

 

 

Share this post


Link to post

It's been a while since I was in the real thing, so I don't remember what the aileron deflection was when we did control checks. When the Aerosoft add-on was in development, there were several real world and current pilots that validated things like that. If you can come up with photos from a real Twin Otter (100-300, and the 400 separately) showing full travel aileron deflection each way, and if the sim VC is markedly different, it would likely be considered for a fix when/if the project is reopened. On the other hand, just comparing Twin Otter aileron deflection with a couple of sim add-ons isn't really valid.

Share this post


Link to post
8 hours ago, Christian85 said:

cant understand why is the Yoke movement not fully 90°degrees in the Twin Otter (Virtual Cockpit)   look on the new AN-2 or Default Cessna 172 /Maule etc ! 

 

Well maybe because it's not an AN-2 / Cessna 172 / Maule /etc. (!)

 

About 60 degrees looks normal (1:15):

 

 

Share this post


Link to post

Thanks, Mark. The depicted control check validates well that full aileron travel is something less than 90 degrees. The object of a control check is to get full deflection of the aileron and elevator, and the one in the video is a textbook example. If separate nosewheel steering is available (so the rudder pedals only control the rudder), you'd check the rudder for "full and free travel" too.

Share this post


Link to post
vor 7 Stunden , MarkHurst sagte:

 

Well maybe because it's not an AN-2 / Cessna 172 / Maule /etc. (!)

 

About 60 degrees looks normal (1:15):

 

 

This are 60Degrees are 85°  the as the B737...  and on the Aerosoft Otter you have only 45° 

 

:(

Share this post


Link to post

Christian85, re: "cant understand why is the Yoke movement not fully 90°degrees in the Twin Otter (Virtual Cockpit)   look on the new AN-2 or Default Cessna 172 /Maule etc ! " (exclamation point in the original). The aileron deflection in the video (left pix) is somewhat less than 90 degrees (the left yoke horn is not vertically over the right one and the top of the yoke clipboard isn't vertical), and the Aerosoft one is less than that at least in the -300 version (right pix). However, since you're the first to comment on it since the extended version was released in early 2014 and the base before that, it appears that to most users, it's a big "so what?" As noted, it's highly unlikely the developer will work to change such a small cosmetic issue. It may be considered if/when the Twin Otter get the go-ahead for the "Extended extended" version.

 

DHC6 Aileron Deflect.jpgAS DHC6 Aileron Deflect.jpg

 

Share this post


Link to post

I made a note of this any if we ever open the project will look at it again. We decided to do it as it is because of the rather silly animation of the yokes where they move to the final position in an accelerated rate.

Share this post


Link to post
On ‎24‎.‎12‎.‎2017 at 09:17, Mathijs Kok sagte:

I made a note of this any if we ever open the project will look at it again. We decided to do it as it is because of the rather silly animation of the yokes where they move to the final position in an accelerated rate.

 

Thank you @Mathijs Kok

 
 
 
best regards 
 

 

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×
×
  • Create New...