Jump to content
Frank Docter

Chaseplane views for the CRJ

Recommended Posts

Hi all, 

 

just to get you started with the CRJ, and when you also have Chaseplane, you can download my presets from the community section of Chaseplane. Just look for TheDude. I did not do engine and wing views and the like. Only the cockpit views I use most when flying the CRJ. 

 

Have fun!

  • Upvote 9

Share this post


Link to post

Amazing! Thanks, Frank. 

Can't wait to get home to try it out.

 

Thanks again for all your contributions!

Share this post


Link to post
On 8/1/2017 at 2:09 PM, Frank Docter said:

Hi all, 

 

just to get you started with the CRJ, and when you also have Chaseplane, you can download my presets from the community section of Chaseplane. Just look for TheDude. I did not do engine and wing views and the like. Only the cockpit views I use most when flying the CRJ. 

 

Have fun!

 

Do you have a link to these files? I assume they at AVSIM? Can't seem to find them.

Thanks in advance.

Share this post


Link to post

No you download them from inside Chaseplane. check the community section.

  • Upvote 1

Share this post


Link to post
Just now, Mathijs Kok said:

No you download them from inside Chaseplane. check the community section.

 

Ah okay... sorry for that one. Thanks for correction.

Share this post


Link to post

I'm having issues with ChasePlane and the CRJ views. When I go from outside back to inside the Captain Standard view keeps defaulting instead of the ChasePlane default. Is there a way to turn off the CRJ default camera system. Only happens with CRJ and since I updated to the new V1.0.0.2. This did not happen with original release. 

  • Upvote 1

Share this post


Link to post

There was no change in the view assignments between the versions. And Chaseplane fully disables the default system....

Share this post


Link to post

You might have to check "Enable Keyboard" or "Controls" in your P3D settings if they're disabled. As long as you use FSUIPC for controller assignments you should be fine to disable them.

Share this post


Link to post

It's a cache file and it's in program files x86 folder I believe. 

Share this post


Link to post

It's whatever directory you installed Chaseplane into...

 

Share this post


Link to post

Hi

I too am having weird behaviour with Chaseplane and CRJ.  The inboard views only work if I boot up a default aircraft and then the CRJ.  As soon as I go to outside views, the screen flashes a lot and then settles to the outside view and all other outside views work OK.  However, going back to inboard views and I get just a default view but all other views do not work.    Also in inboard mode, the Chaseplane defined key assignments (for movement of view) are incorrect, but OK in outside view.   I can see two cache files in the Chaseplane folder, "cache" and "cp_cache".  I have tried deleting either of these but no success in solving the problem.   This behaviour occurs in both my P3D v3.4  and my P3D v4 installations on the same computer.   All other aircraft in both installations work normally with Chaseplane.  Any ideas?

 

Share this post


Link to post

I have no problems but i fly on FSX. I have done a nice set of inside and outsideviews for the CRJ. I will upload the set in the next few days. Look for maxhades!

 

Max

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...