Jump to content


  • Posts

  • Joined

  • Last visited

About rolle

Contact Methods

  • Website URL
  • ICQ

rolle's Achievements


Newbie (1/14)



  1. Hello, the flight following function in airbus x connect is a very nice addition. Are there plans to expand this function in further Versions? What i miss is the remain-time/distance to the departure, or the distance to TOD, or the ground speed. If this would be added, that would be very nice! Greetz
  2. Thanks for that. I tried this and reduced the frequency on the ND and PFD xml's. Now i have about 3 to 4 frames more. At the moment it's ok for me, because the slideshow goes into an acceptable motion. The next thing is the the reaction of the N1, as i described in the first post of this thread. What i obeserved is, that the N1 doesn't, or very very low, decrease when the indicate airspeed goes into overspeed. An overspeed situation accure when winddirection and speed are changing or you go into descend. Sometimes, the N1 shows absolute no reaction, although an Idle position would be the better way. Greetz
  3. Hello Mathijs, nice to read this. But i have to say, that the FPS changes are not marginally! With version 1.11 FPS on Ground (and when turning) at about 18-22 fps. Now, in conjunction with an Addon, down to 6 to 7 (when you are turning, <- and only then). Thanks for that. I've tried this and changes the frequency value from 18 down to 5. The fps are now 2-3 frames better, so there have to be another reason for the lower fps. I hope we can go back to the old very good framerates and in addition to solve the overspeed issue (see above) . Greetz, Dirk
  4. Hello Michael, perhaps it has different reasons, but can you tell to us how and where do change the refreshrate of the ND's? Thanks Grz
  5. Hello, i think the cause of the low framerates are the higher fps of the ND. When i taxi and the compass (ND) doesn't move i have an excellent framerate, but when i make a turn the frames going deep. So, it would be nice when Aerosoft can give an 'quick-fix' . With these frames actually the update is an step backwards, in spite of the good other improvments. In my judgement, higher frames on the ND are not very important. For me, the ND-frames from the first Version was acceptable. Grz
  6. Hello, at first, this new version brings a few great improvments. But for me there is a massive new problem: With this Version 1.20 my Framerates are now very low. I used the same route, the same Scenery on my last flight. Especially on Ground and lower flightlevel are the FPS down to 10. Further, the AP doesn't reduce the Thrust or to low in managed mode, when you're going into descend. Conclusion of that is, that the Airbus is in overspeed. The next thing is, that the nosedip-problem (when deactivating the AP and at 100ft) is still existing, but not so strong as in Version 1.11 Grz
  7. Wow, I see a cruise speed of M0.78 Grz
  8. Hello, most of these points already wrote. My 'wishlist': - An Advanced Version - Sid/Stars - VNAV - editable F-Plan (Alt, Speed) - Navigraph Database - keeping up the good FPS, insofar as possible - proper FBW-model - fair price for the standard-version customers Grz
  9. I hope not, this issue is actually not acceptable. It can't be true, that i have to avoid a nearly crash on every landing. Thus, i disconnect the AP at about 1000ft so that i have enough space to recover. It would be nice, when Aerosoft express oneself to this issue. A word if you registered this problem and if you work on this, would be nice. Grz
  10. ehm, i have to correct my last reply. After my flight with M0.78, the last two flights doesn't reach values over M0.705. These last flights had a steplclimb, could this be a possible reason? Grz
  11. Hello, in my opinion, the last update was a good step forward. I can't subscribe Craigs view, because the climb-performance is much better than before. Also the cruise-speed reachs now M0.78. Be sure that you download and install the Version 1.11 and don't forget to deinstall the previous version first. Grz
  12. Hello, thanks for your replay, indeed that was the problem. I've copied now the files to the correct folder and now its worked. Thanks! Grz
  13. Hello Mathijs no, when i choose any (equal if cold&dark, ready for taxi or what ever) state, there is always an cold and dark situation. In addition, a few knobs does not working any longer. when i click on this knobs they're not "moving" and shows no interaction. At the beginning, when i loaded the aircraft, the knobs are still working. Grz
  14. Hello, when i load the Airbus the systems and engines are running. Now i want to load the cold & dark state. When i choose this state on the MCDU, the Cockpit is cold and dark, but after this a few knobs and are not working. The same result at the other states. What is wrong? Grz
  • Create New...