Jump to content


  • Posts

  • Joined

  • Last visited

Everything posted by mazelda

  1. Hi, Well i think i've got it fixed. I deleted the configurator and started from scratch and created a couple of test copies of the yoke and throttle. This time it all worked perfectly, although ive not added any new bindings yet all the default keys and led's look to have copied over. I can only assume i had a corrupt install of the configurator. But this time it all seems good Thank for the help
  2. Ok, interesting, I made copies of the default throttle and yoke and using the honeycomb configurator activated them then started p3d. Nothing worked. Ive just tried again but using the original default profiles and this time it worked. Is it possible then that if you make a copy of a profile it does not always save the various bindings. Scratching my head here all strange
  3. Ive loaded the default profiles for the yoke and throttle andim trying it on the default p3d mooney
  4. Yes i have yoke, throttle and reload all bindings 5 in total However when i select show bindings for throttle or yoke i get nothing And ive tried a few of the buttons but getting no actions eg flaps up or down gear up or down
  5. Ok thanks, It looks like i have a problem then as i don't get the green bar at any time.So it looks like the honeycomb configurator is not linking to P3d Should i have any entries in the addons.cfg for honeycomb? Anything else i can check? Thanks
  6. Yes that answers my question thanks However,I cannot seem to get even the default profile to work in p3dv5. I'm not sure what i'm doing wrong. Does p3d need to be running when i activate the profile ? When i start p3d my throttle quadrant shows up in the choice of controllers but none of the default profile buttons or lights work. So it looks like the profile has not changed any of the button settings in p3d I've been trying on default p3d aircraft, so any lvar's should not be causing the issues. Hope you can advise Many thanks
  7. Many thanks If after activating the profile and starting p3d I save that profile config in p3d that profile should be saved within p3d Therefore if I have several honeycomb profiles saved in the honeycomb configurator and those are transfered to p3d, saved as individual profiles in p3d does that cause any conflicts swapping between them in the flight sim?
  8. Hi, I'm just starting to use my honeycomb throttle and yoke and I was wondering if i have to run the configurator before starting P3d every time, or if you have a profile downloaded or created in the configurator once you have sent it over to P3d I can save it as a config in p3d and therefore do not need to run the honeycomb configurator before starting P3d Thanks
  9. Hi Guys' I hope I can explain this properly I'm using MSFS I've changed the switches more to my liking on the bravo throttle quadrant but the led's now either do not work or show the wrong LED for example i've changed one of my switches so that my park brake is easier to flick on and off but the LED for anti ice comes on when i do this. How do I change the switch LED combo so that when I turn park brake on the park brake LED also illuminates and not the anti ice LED Thanks
  10. hi, I found a sort of solution on avsim forums and it DOES work for me at least.I've not fully tested everything but I do now get lights. when I run the sim Hopefully your guys can figure it out and create a fix. ok so here is what they said and what I did In the afc bin folder that is in your community folder copy and put the afc bridge exe file as a desktop short cut. make sure you give it admin rights. Start msfs in admin mode although I don't think this is neccessary. when you have created your flight and are ready to hit fly, run the afc bridge exe from your desktop then hit fly. Once your flight is loaded you should have your lights back. It has worked twice for me but its by no means an ideal solution hopefulyy with this info Ben can figure out why and offer a fix cheers
  11. Hi , Add me to the list I have carried out what you requested. All lights work with the test program When i created my install I used a custom location for the msfs install so my community folder is E:\Flightsim drive\MSFS2020\community\AFC Bridge\Bin And have the same 2 files as baxterbj in that folder MSFS still shows AFC_Bridge as not installed All My other addons that are in the community folder work perfectly so MSFS sees the folder fine Thanks
  12. Hi, been away from the sims for a short while but i just discovered an issue with my bravo throttle quadrant regarding the lights on the quadrant which had been working and still do on my p3d installs. however in msfs they have stopped working . I noticed that in my contents folder the afc bridge shows as not installed but is in my community folder. i have uninstalled the afc bridge folder redownloaded and reinstalled the latest msfs fix for the lights from the aerosoft site to no avail. from what i have read this may be the reason i cannot get the lights to work but no matter what i try in msfs i cannot get it to recognise the afc bridge as being installed. I remember there being an issue with 3rd party programs showing as not installed but were actually working. I had this but with the various sim updates since this looks like it was fixed except for the afc bridge in my case any ideas? thanks
  13. Thanks Mathijs, I have done as you suggested, hopefully your guys can help with UPS as UPS have been useless. Thanks
  14. Hi Guys, Hope you might be able to help with this as I am getting really fed up with this. I purchased the Honeycomb alpha and Bravo hardware back at the beginning of January. While I knew there was going to be a wait I was prepared for this. So fast forward now until the 7 April when I get an email from Aerosoft saying that my Alpha and Bravo items had been dispatched. Fantastic! However that's where it ends. You have used UPS to deliver the goods. I received an email from them regarding import duties which I was prepared for, and these where paid on the 12April in full. In between that I have received no less than 12 redelivery dates some for the same date and time. Because they require a signature, I rearranged my work schedule to suit. that time came and went and no delivery. I then phoned UPS the following day and was informed that the packages were still in Germany, Herne-Boernig to be precise, and that they had just cleared customs. The latest delivery date was now the 19 April. I was not happy as this was nearly 2 weeks since you had shipped the package. But ok , I then today got another email saying that it is now the 20 April. At which point I phoned UPS again as the tracking number said it was still awaiting clearance to export, after a lengthy phone call, I was then given a number to call in Germany to find out what was happening, but this number is not reachable from the UK and they cannot transfer me from the service centre to the number I was given. I did eventually get a number for the German service centre, but it was obviously in German, and sadly I speak no German. I appreciate that none of this is really your problem, however if they loose this package it may become your problem, as I will be looking to get a replacement from yourselves which no doubt will then lead to yourselves requiring a refund from UPS. Also if this happens I will not be expecting to wait 4 months for replacement items to be delivered. If you can offer any help i will happily give you the details of the tracking number and invoice numbers via email not through general forum posts. even if its only calling the number to find out what is happening. Many thanks for any help you may be able to provide Peter Little
  15. mazelda

    Import taxes

    Hi guys, Not sure if you will be able to answer this or if it will have to be through customer services.Hopefully as management you should have some ideas. I have recently placed an order for the honeycomb yoke and throttle quadrant placed after the UK left the EU. Since i purchased these items that you requested payment up front, there have been a lot of horror stories regarding import duties and VAT to the UK. To the point that some people have been quoting that they are paying almost the same again in VAT and import duties. This as you may imagine is very disconcerting having already paid for something. Therefore could you please tell me how much, if anything that i may have to pay for this hardware that i have purchased. The delivery note says due in the spring, so i would like to know well before if i will be due more and what my options will be. Many thanks
  16. Hi As I do not own the crj pro package and still have the original release, are there plans to make this compatable with p3dv5 or is it already compatable I have not decided weather I want to upgrade so any info would be helpful thanks
  17. Hi, I know this is my fault but I'm not sure i'm understanding how to implement sode jetways in EDDF. I'm running P3dv5 with the latest updates from Orbx and the 2.000 for EDDF however i'm not sure what i'm doing after that. I've unzipped the sode file fine. but after that I'm doing something wrong. The readme says 1.) Copy the Subfolder SODE below the "Mega Airport Frankfurt Professional" (P3D V4) or "Mega Airport Frankfurt Professional V5" (P3D V5) Folder of the Scenery Addon. Does this mean the scenery library of P3D? Or does it mean copy the folder into the Mega Airport Frankfurt Professional V5 folder? 2.) Start the SODE-ON.BAT Batchjob File, to aktivate the SODE Jetways Every time I try to do this the batch file says it cannot find the 3 files to copy although at the end it does say sode jetways activated. Could someone tell me if that is normal ,or what I might be doing wrong. Thanks
  • Create New...