Jump to content

AlleUsai

Members
  • Content Count

    22
  • Joined

  • Last visited

Community Reputation

0 Neutral

About AlleUsai

  • Rank
    Flight Student - Groundwork

Recent Profile Visitors

116 profile views
  1. Rolf, will do it ASAP and I'll report If the issue comes again. Thanks, Alessandro
  2. Hi Rolf, After takeoff what did the INFOBAR state? Did you see the message CLIMB TO CRZ LEVEL or something similar? No, I was expecting for it but it never appeared. Did you reach the flight level enetered in the MCDU? Yes, I did. Cheers, Alessandro
  3. Hi, today I made a flight with A321 (Lufthansa) using checklists. Everithing was good since after takeoff. At this point the aircraft was climbing to the final FL but no checklist was working after "After Takeoff CL". I've finished my flight without CLs. I'm using Airbus professional experimental version on W10 64bit, P3D v4.5 HF3. Is there a "reset CL" option in order to restart checklists flow at the current flight phase? Thanks in advance, Alessandro
  4. Hi, today I made a flight with A321 (Lufthansa) using checklists. Everithing was good since after takeoff. At this point the aircraft was climbing to the final FL but no checklist was working after "After Takeoff CL". I've finished my flight without CLs. I'm using Airbus professional experimental version on W10 64bit, P3D v4.5 HF3. Is there a "reset CL" option in order to restart checklists flow at the current flight phase? Thanks in advance, Alessandro
  5. Ok Otto, it was my fault. Thanks a lot, Alessandro
  6. No, I didn't. Is mandatory to do it if the expected cruise altitude is never reached before starting descent phase? Alessandro
  7. Hi, yesterday i did a short ride from ENBR to ENVA using (as usual for me) ProATC-X. In flight plan the cruise flight level was 350 and I set this on MCDU. I was on CLIMB phase and everything with checklists was going fine. Before reaching FL350 ProATC (altitude was about 31000 feets) asked to descend to FL240. I did so but checklist was stuck on CLIMB phase so I did the rest of flight without CLs. Is it a normal behaviour or did I something wrong. I was not able to "reset" CL and start then BEFORE DESCENT one. I use P3D v4.5 HF3 and experimental version on Airbus Professional A320/A321. Thanks in advance, Alessandro
  8. Hi Dave, finally I sorted out some test on checklist system. As I seen checklists starts normally on cockpit preparation then doesn't activate after GSX pushback phase. Must I open a ticket for this issue? Thanks, Alessandro
  9. Hi Juergen, I'll check both on the next weekend. AS support notified me that this will be fixed in a future update. Have a nice day, Alessandro
  10. Hi Juergen, I'm quite sure that your suggestion could be valid. I want to test original AFCAD with ProAtc X (arrival gate assignment, etc) and with AI Traffic (UTL) for any issues. Alessandro
  11. Hi Jurgen, thank you. I know this way but Aerosoft Support said "this does not appear to be correct". Waiting for AS Support early news. Have a nice day, Alessandro
  12. Hi, just bought Aerosoft Mega Airport Rome v1.4 on SimMrket web site. I use P3D v4.5 HF3 on W10 (10.0.19041 Build 19041) and I see all gates and parking are designed RAMP_GA except parking 101, 102 and 103 that are RAMP_CARGO. Is this correct? I think not but may be I'm going wrong. Any hint? Thanks in advance, Alessandro
  13. Hi Dave, yes, printer and its sheets of paper seem to work correctly now. I'm aware of fire test issue is fixed and will be released with next update. Now I want to test again if checklists work. I'll let you know. Thanks again, Alessandro
  14. I Dave, I've done all tasks you gave me. I've updated to experimental version 1.3.1.1 and all outputs are similar to yours. And the printer printed and the sheet is visible and filled with correct values. As requested I'm attaching the Aerosoft folder after the Uninstall task. Looking forawrd for your advices. Regards, Alessandro Aerosoft_AfterUninstall.zip
  15. Hi Dave, thank you for your reply. Unfortunatly I'll be out for holiday for a couple of week so I can't try to unistall and install again following your notes. I'll do after the 23th of August. But I can send you my current Data folder and answer to your questions: 1. Are you using P3Dv4.56HF3? My P3d version is P3D Professional 4.5 HF3 4.5.1434698. 2. What is the specific location to which P3Dv4.5 was installed to? C:\Program Files\Lockheed Martin\Prepar3D v4. 3. What is the specific location to which you installed the Airbus? C:\Users\alleu\Documents\Aerosoft. 4. Are you certain the product was uninstalled a check was then made for for any remaining product folders and files, a reboot was performed before installing the product again? Yes I do. 5. The current download version of the Airbus A320/A321 which installs is version 1.3.1.0. The AS Updater will then install version 1.3.1.1, but one should reboot before installing that update and the AS Updater should be run as Admin. I've done a reboot after run of AS Updater and apply 1.3.11 version. 6. Would you kindly zip and upload your "Data" folder in your reply in this thread? It will be located in the Aerosoft A320-A321 folder where you installed the product. Please see attachment. Thanks again, Alessandro Data.zip
×
×
  • Create New...