Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by Alessio75

  1. You can find the Tutorials pdf into the Aerosoft's documentation folder of your pc.
  2. Hi, could you replicate it an other time? Start again Fsx, load the plane.. and select KDFW departure as you did.
  3. I think is feasible but I guess it was not implemented in order to don't impact frame rate too much
  4. I'm afraid that ice runway impairs some customized friction variable in this product
  5. I'm sorry, I make a different question. Does it appear only during push back? Or every time?
  6. So, does it appear without a push back condition?
  7. How was your framerate? And your time compression rate if you increased it?
  8. Thank for your clarification, but the problem is a very short flash message on ECAM that immediately disappears and it can't be read
  9. Thanks, so there isn't a fix looking into xml files? I just tested rudder trim to see if it was a momentary warning issue too, and it was
  10. Hi, I think I have an issue with warning messages on ECAM. "Speed brake still out" appears and disappear suddenly as it pops up (i.e. leaving speed brakes for too long in flight). As well as when I did this such of test: before take-off I moved rudder trim to full left and I pressed TO Config: I get the warning "rudder trim not ..." but it suddenly disappeared. All these warnings are almost unreadable as they disappear very quickly from Ecam display I have v1.31, Fsx sp2, on Win10.
  11. Hi, did you try to set 121.77 in a default aircraft? However i think the sim only accepts definite increments
  12. Right click on the A/Thr button. Be aware about thrust levers position as stated above!
  13. Hi did you fill all the required fields in the MCDU?
  14. Thanks for clarify. But my original question was that during preparation CL this button is pressed ON. I cannot find the moment in the checklists when it is turned off.
  15. Hi thank you. I was referring to "elec pump" push button. It has only on and off position
  16. Hi, waiting for more expert people, i have just two questions. Do you have an updated Airac intalled in your Mcdu? Did you check for any plan discontinuity in f-plan page?
  17. Thank you for your reply. But what is the procedure during a selected/selected NPA? Should I press aprr button as well?
  18. Hi, when I turn on the switch "ann lt" to Test, I discovered a red light indicator on PFD that normally I don't see on during autoland. When it comes on? Thanks!
  19. Hi, during NPA I have the following issue. When I press trk button on FCU and I select the glide angle, I read FPA xx° on PFD - ok it's right. But as I pass through a previous displayed altitude in FCU (ie 3000 ft) the PFD indication changes to ALT●. I need to press for level off and select again the path angle to have back FPA xx°. Is it a correct behaviour? Thanks for comments about!
  20. Hi, I'm using CumulusX! in FSX (Sp2), in Win10, with Steve's DX10 fixer. I have vertical jitters problems in outside view. In the Help file, a solution is proposed as a DLL package to be downloaded from Authors website: but on this website I cannot find the download link to test the new DLL package. Can someone help me? Thanks!
  21. Hi, not sure if I understood, but Loc button follows only horizontal navigation by a Localizer signal. To have a descending glide slope you need to press Appr button (by ILS signal).
  22. Hi I have just bought ASK21 for Fsx sp2. Everythingis ok except I can't modulate the vario sound on C4 computer. I have no sound at 0 (ok) and full sound from 5 to 100 value
  23. Ok thanks! I have just found tha you have ASK21 as well. So what is the best to make pleasant flights in Fsx?
  24. Probably because FPS drops below 10 and the plane flight is pretty unstable under those values (due to fly by wire system variables communication I guess)
  25. Hi, I'm going to buy one of the two Aerosoft's gliders. What are the differences between Discus X and Discus K? Except price. I use FSX-Sp2 on Win 10 (notebook) Thank you
  • Create New...