Aerosoft official retail partner for Microsoft Flight Simulator !! 
Click here for more information

Jump to content

divinglyc

Members
  • Content Count

    58
  • Joined

  • Last visited

Posts posted by divinglyc


  1. Hi!

    I know this issue has been mentioned and discussed a little bit before.

    That is, after I play the replay when I have parked my aircraft at the gate, the plane would be on an unexpected acceleration mode. There is no exception and bothers me a lot.

    I could not find a solution or conclusion according to previous threads.

    I just wonder if there is any solution now for this?

    Thanks a lot! 

    ps. P3D V4.4.


  2. I also have the same issue. 

    My FMGS showed managed speed is 326, but on the cruise, the plane just decided to set the spd to lower and began to decelerate. I had to manually set the selected spd to 326 to maintain its speed. It was a flight from NZCH to NZQN with A320-IAE.

    Also v1.2.2.0 and I have reinstalled the whole Airbus for 3 times.(P3D v4.4 upgraded with Client and Content)

    2018-12-19_17-6-21-416.png


  3. 16 hours ago, Hanse said:

    Hi,

    I had some other ideas what could cause your problem:

    • Did you disable the NSW Steering / Tiller before doing the Rudder Check? This is RW ops......
    • Maybe you should re-calibrate your rudders......
    • What does the rudder trim on the pedestal states......

    Regarding the video issue I suggest to open a new thread in the right section because then specific people (with the resp. knowledge) will look into it...... Please, never use one thred for various issues....

    Regards,

    Rolf

    Hi! Hanse,

    Thanks a lot for your hints.

    • Did you disable the NSW Steering / Tiller before doing the Rudder Check? This is RW ops......--> I have set Tiller:on, Disconnect tiller with rudder, Auto rudder: off
    • Maybe you should re-calibrate your rudders......--> done many times for this
    • What does the rudder trim on the pedestal states......It is 0,0

    I also find it's Checklist related. If I don't run the checklist, it's OK. If I run Checklist, and Copilot off, even if I skip the Flight control check step, this still happens. However, if I run Checklist with Copilot on, this will not happen.

    Pretty weird....

     


  4. 24 minutes ago, Hanse said:

    Hi,

    sorry but then I think this has nothing to do with the CL but with the setup of your joystick / rudder...... I am also not able to reproduce this problem and until now no other user reported such a problem. The only thing I can suggest is that you open a support ticket and then someone will try to find / solve your specific problem...... Sorry.

    Regards,

    Rolf

    Thanks!

    I will do some more tests after I install Content of P3D v4.4 because I only installed Client for v4.4.

    Hope it works.

    BTW, what about the video issue? Sometimes I can see the image on the ECAM monitor, but sometimes not... Why?


  5. 1 hour ago, Hanse said:

    Hi,

    does this also happen if you use "SKIP ITEM" for the rudder check? What are your settings

    • P3D v4.4 Options / Realism / Flight Controls - Use Autorudder = unchecked?
    • MCDU3 OPTIONS / AIRCRAFT / AUTO RUDDER = OFF?

    Regards,

    Rolf

     

    Hi! Hanse,

     

    Thanks a lot for answering me.

    I have tested it. This happened also even if I skip the item( Flight control test).

    • P3D v4.4 Options / Realism / Flight Controls - Use Autorudder = unchecked?--> Yes, unchecked.
    • MCDU3 OPTIONS / AIRCRAFT / AUTO RUDDER = OFF? --> Yes, Off.

    Please help me. Thanks!!

     


  6. Hi!

    I have had this Airbus(A320/321) since P3D V3.4.

    A few days ago, I purchased it again for P3D v4.4.

    I enjoyed the aircraft along with its immersion, like the checklist procedure.

    However, I have encountered 3 times( not every time) that while doing Before taxi checklist, the Engine and all electricity was all cut out suddenly while I press my rudder axis(during Flight control checklist).

    Therefore, I have to Connect GPU, start APU and then start the procedure from cold and dark all over again. I have to enter my flight plan into FMGS again, too. 

    Besides, the Cockpit entry video sometimes work, sometimes not. WHy is that?

    What could be the problem? Thanks a lot for any help!

     

    ps. Windows 10 pro. v1803.

         P3D v4.4( upgraded with Client installation)


  7. Hi!

    I have just begun my first few flights of the A320. I read from the manual that I can use the AOC uplink of weather data.

    I can see my dept. and arrival airport in the list and then Request weather. 

    However, in the received message, there is only weather data of the departure airport, no data for arrival airport.

    Is it normal or what?

    BTW, the departure/arrival airport were LSZH/LOWW

    Thanks!


  8. On 12/14/2018 at 11:28 PM, DaveCT2003 said:

     

    Have you run the ASUpdater?  If not, please run it "As Admin" and select to install Experimental Updates.

     

    Let us know how you make out?

     

     

    Hi! Dave,

    Thanks! I have updated the plane and the incorrect alt. readout has gone.

    Thanks a lot!


  9. Hi!

    I have just purchased A320/321 and just installed.

    When I fly with Checklist/Co-pilot on, the readout of altitude is not correct( eg. Co-pilot read "passing 10000 ft" but in fact it was 14000 ft, or while descending, co-pilot readout "1000 ft" but in fact it was about 2500 ft.)

    What have I missed or is it a bug?

    Thanks a lot! 

×
×
  • Create New...