Jump to content

Garyo

Members
  • Posts

    56
  • Joined

  • Last visited

Everything posted by Garyo

  1. Dear Mathijs,

     

    Could you direct to the right person who might be able to help me with this file problem on the CRJ?

     

    I'm unable to load a saved inflight CRJ file.  As far as saved files go, the CRJ seems to work ok with on-the-ground saved files, but something is not working inflight. Note that the gear  is down, both engines are off and the CDUs are off.    The saved file should have been: level at FL370.   Any ideas?  BTW, the 320 inflight saved files seem ok.

     

    Screenshot (10).png

  2. Tom, The A320 seems to be working fine. However, I'm unable to load a saved inflight CRJ file. As far as saved files go, the CRJ seems to work ok with on-the-ground saved files, but something is not working inflight. Note that the gear is down, both engines are off and the CDUs are off. any ideas? BTW, the 320 inflight saved files seem ok. Thanks, GaryO
  3. Correct. Alpha Floor is an AUTOTHRSUST protection. I think I meant Alpha Max. My point is, the Speedtape presentation is not correct. I think the problem is that I set up the cockpit while running the APU. When I set "READY FOR TAKEOFF" that is when the sim seems to have lost some data after engine start.. Happy New Year, GaryO
  4. As the screenshot shows, I'm unable to load a saved inflight CRJ file. AS far as saved files go, the CRJ seems to work ok with on-the-ground saved files, but something is not working inflight. Note that the gear is down, both engines are off and the CDUs are off. any ideas? Thanks, GaryO
  5. Everything is setup correctly, as far as I can tell. There may be a glitch when I switch from "Ready to Taxi" to Ready for Takeoff". It seems that when I run all checklist with the aircraft in the "Ready for Takeoff Mode", the aircraft responds as it should. I will investigate further. This is a new sim for us. Previously, we used the FSLabs A320 simulator running on P3Dv3. Merry Christmas, GaryO
  6. SRS is now engaging. The problem is it is not commanding V2 +10kts. The indicated Magenta speed bug is to slow.
  7. Question. After departure flying the A320, the SRS should command V2 =10 kts. Prior to departure the speed tape shows V2 at 129 kts. During the initial climb, SRS has not increased to V2 + 10, although it shows active in the FMA col 2. Also, I don't think the Speed tape is representing Alpha Floor correctly. Alpha Floor appears to be to fast. Departure weight out of KSFO runway 1R is 144,000 lbs and V2 is 129 kts as displayed in the PERF Page. Thanks, GaryO
  8. I'm pretty sure everything was done. SRS should come on before 80kts.
  9. After departure, I noticed the SRS not active. At about 200' agl, I put the A320 on AP 1. The aircraft slowly pitched up and activated TOGA LOCK . The auto thrust system seemed ok after passing the Thrust Reduction/ ACL altitude. Has anyone else had this problem? Thanks, GaryO
  10. Tom, One question. What am I doing wrong on loading fuel. I used the 320 Fuel Planner, and the data appears to have transferred to the MCDU Perf Page, However, the actual fuel on the on the aircraft Upper ECAM is 18600 lbs, but the fuel I requested is 23100. I can't quite figure this out. Thanks, GaryO .
  11. Thanks Tom, I did find the files. I just needed to know where to look. The sim looks very nice. GaryO
  12. Dear Mathijs, We are still having trouble locating information in the start menu. When I search Aerosoft I get the first screen shot. When I try to open the file, I get the second screen shot. Am I looking at the wrong files? GaryO
  13. I'm apparently having some difficulties accessing the Documents section. When I search Sim\Aerosoft\Airbus\A320_A321\Documentation in the start menu, nothing comes up. I'm very familiar with the Aerosoft CRJ, but we (ERAU) just switched to the Aersoft A320 for FMS instruction. I know the airplane (Delta CA on the 320/330 for 12 years), but I just can't seem to located the info I need to get the aircraft going. Thanks for your help. Prof. Gary Vessell
  14. One quick question. How do I get the MCDU (FO) to go into the "Aircraft State Mode"? GaryO
  15. Where might the tutorial and documentation be located? GaryO
  16. "WE" is Embry Riddle Aeronautical University in Prescott, Arizona. We have used Aerosoft products for several years, and have switched back to A 320 after using FD Labs A320. I use this aircraft to teach FMS to hopeful airline pilots. Gary "
  17. We just purchased the newest version of the A320/321 for Prepare V5. I am a little confused on how to input data, such as fuel and passengers, into the FMGC. Could you direct me to the information source that might help me out? Thanks, Prof. Gary Vessell Embry Riddle Aeronautical University
  18. Dave,  I recently downloaded the CRJ v1.2.  It did not go well.  I was previously running V 1.01(?) without any problems using P3D V 4.0.28.  After downloading the new version I have screen problems and the program shutting down. DAVE was also inop.  See the Screenshot.  I use this program as a teaching tool, so any help would be greatly appreciated.

     

    Thanks,

    GaryO 

    Screenshot (67).png

    1. DaveCT2003

      DaveCT2003

      Hey Gary,

       

      I'm sorry to hear you're experiencing problems and I know how frustrating that can be.  However I have to sincerely apologize, but I've not worked the CRJ for at least six months and I've been so darned busy with the Airbus Pro and I'm really not up to speed on the CRJ tech support wise.  I do see that Hans replied to you (though I didn't read it), and there is absolutely nobody better to assist you than my good friend Hans (after all, he wrote the software!).

       

      I'm sure Hans can help you (he's the top of the food chain for the CRJ and many other terrific products), but in the off chance that you're not able to resolve the issue (which would likely mean it's either an install or P3D related issue) then please send me a Private message linking to what you've also posted in the forums and I'll do my very best to carve out some time to get the CRJ updated and will try to help you.

       

      Best wishes.

       

  19. Garyo

    Garyo

    Version 1.0.0

    0 downloads

    I keep getting this after start up. The program shuts down after the file shows up.
  20. Dear Mr. Kok,

     

    After downloading the CRJ sim, I am getting several error messages.  The first is: "unable to open userwpt.txt.  The second is: INVALID_HANDLE_VALUE.

     

    Any ideas?

     

    Thanks,

     

    Garyo

    Screenshot (16).png

  21. Thanks, Tom.  

     

    We are using Prepare 3D v2.  All screens appear normal.  However, I cannot input any info into the MCDU.  The MCDU appears normal, but will not accept any inputs.

×
×
  • Create New...