PFD, ND, ECAMS

I'm following Vol6 StepbyStep Guide Chapter 2.1.3 on the weather radar, but so far no returns at all at any range. I'm using ASN, and it was raining at the airport on climb out. The terrain radar works fine, and I can see the radar scanning. When I switch to wx or wx + t then I get no returns. Any ideas what could be wrong? I'm running the most up to date version of P3d and FSUIPC, if that even matters.

I am currently flying KMSP-KDEN in the Airbus x a320. I have fsx weather set to real world weather w/o updates, and my weather radar is displaying severe thunderstorms nearby, but when I look out my window, there aren't any. Is this an Fsx problem, or an A320 problem, and if you have any ideas on how to fix it, that'd be great! Here are some pics. Oh, and tilt is set to 0, gain is set to cal, and the selected mode is wx+t

Hi all, Just noticed that when you click on the HYD page on the lower ECAM there is low quantity in the green system. Attached is a picture. Cheers, Matt.

Just a recap. Installed AirbusA318-A321 on Fsx steam and P3dv3 worked fine (and the master caution). Somehow I erased all my desktop item with some type of security allowing access to sub folders. So I had to perform a system restore and had to reinstall fsx and prepard3d (STUPID ME). KICKING MYSELF ON THAT ONE!!!!!! Reinstalled airbus on P3d and ended up with this NO ROUTE DISPLAYED ON ND ISSUE!!!! Went online and checked forums from google and Aerosoft forum website with no luck, Found similar topics but no probable solution was posted or if a solution was posted they didn't clearly specify how to fix the problem. This is probably a revisited issue. Please giv…

Hi guys, im having a problem only with the a321 IAE and CFM where every screen is displaying the appropriate information but the screen on both sides that displays attitude, airspeed, altitude etc is black and nothing is showing, it hasnt done this before and only recently did this, thanks very much for any help.

So I am currently having a problem with my displays not working on the airbus a318, a319, a320, a321. The pfd is working. But the rest of my screens including nd, eicas, etc, are all blacked out. Is there a fix for this?

Hi I have exactly followed the instructions for installing version 1.31 yet I have ended up with no fonts on the PFD.(Please see attached screenshot). I see that in two other recent closed posts about the same problem there is mention of installing the product as the Administrator yet there is no mention of this stage in the Installing 1.31 topic dated 28th October 2015. As I say above I exactly followed the instructions given but didn't install it as the Administrator. Does this mean I now have to uninstall both the A320/21 and A318/19? I would appreciate if you could tell me how I install this as the Administrator. I have not had this problem whe…

I can enter a three digit radial for a VOR FIX only after entering a two digit radial. Should be a programming glitch.

hey guys! Where do I got to cruise page for my lower ECAM. I pressed all the buttons there but nothing shows up

Hello, I have a problem with the screen does not show the speed or altitude. Please help. It's screen.

I connected as slave with my friend, everything look good but data on PFD monitor not show as attach picture. Can you tell me how to fix it? PS. I has turn on Sync Display/ND Overlay already. Thank a lot.

Hey, I just reinstalled my aerosoft airbus 318-319-320-321 and suddenly all text and numbers from my PFD are gone. Before the i reinstalled it everything worked fine. I already reinstalled five times now, but the PFD keeps showing up blank. Any suggestions? I have fsx and run it on windows 7! Thx for the help!

Hi.. There is any idea for those black screens?.. I talking about all the airbus models v1.31 for p3d v3.. The MCPU doesnt work too and the throttle is not responding.. I've tried to reinstall, reboot and this is not working. Please help. My system: Windows 7 SP1 P3D v3. Best Regards, Koren.

Bei dem Add-On Aerosoft A320/321 habe ich ein großes problem. Ich spiele FSX in den niedrigsten Einstellungen um das Add-On zu benutzen und in diesen Einstellungen ist das ND so groß, dass man nur die obere rechte Ecke sehen kann. Also ich sehe nur: GS, TAS und z.B. die Zahlen 22, 23, 24, 25 und 26. es nervt sehr, da ich so nicht die Flugroute, Top of descent und co. Gibt es irgendeine Möglichkeit, damit ich wieder das ganze sehe, was auf dem ND angezeigt wird. Bitte schnell möglichst um Antwort, euer Dominik bzw. Domsche04

I've noticed some imprecision during ILS approach on A320f v1.31 If to push APPR and second AP on FCU above 5000' appears CAT3 DUAL. It's not correct. Must be CAT 1 according to FCOM PRO-NOR-SOP-18 (-Above 5 000 ft AGL, the FMA displays CAT 1.)

Moin zusammen, ich habe aktuell folgendes Problem: Ich fliege die strecke X nach EDDK beim Einstellen im FMC wird mir jedoch beim Arrival nicht der STAR "NOR" angezeigt wie er mit lt. Plan angegeben wird. Ich habe den Cycle 1604 runtergeladen und instaliert - habe trotzdem dass gleiche Problem. Hat jemand einen Tipp für mich?

I'm having trouble with the error message, Error_ Log file could not be generated! 08_08_2015 21_12_36.mp4 ND is blank. I read on the forum that running FSX as Administrator solves the problem. Unfortunately for me, I use FSX-SE and don't think I can run as administrator in that platform. Any advice? Robert Jones

Hello The T.O. CONFIG button of my airbus does not always work (nothing happens). To be precise at the moment I can just manage it to work by loading a pre-defined aircraft state. But even with this it does not work anymore after having flown a leg and getting ready for another flight (except if I load an aircraft state for this second flight again). By "not working" i mean that there are no indications in the left lower part of the Engine and Warning Display. Situation when I expect it to work: Aircraft is on the ground Aircraft is electrically powered (should be obvious but just to mention it...) Both Engines are running (maybe …

I recently bought Prepar3D and reinstalled the Airbuses for it. (yes, after first uninstalling) They are now side-by-side in FSX, FSX-SE, and Prepar3D. Next I added the Navigraph data (Airac 1603) using the installer's "Prepar3D v3" setting. I see them actually present in the "aerosoft\Airbus X Extended" folder, just as with FSX. Configurator also set to Navigraph. Nevertheless, the MCDU proclaims EHAM not to be in the database. Tried Prepar3D both in Admin and normal, no change. Any ideas? Bert

Dear all Can anyone advise me as to how to fix the missing switches / controls when night lighting is activated Many thanks Hyland

Hi, Just something I noticed, the cabin temperatures respond very rapidly to changing temperature selections. This is ESPECIALLY apparent when turning the APU bleed on for the first time from cold and dark/turnaround in cold or hot climates, where the temperature can go from -10 or 45C to 25C within 15 seconds in the cabin. I would suspect that it should take something on the order of 5-10 minutes for a change from -10C to 25C, or 5 minutes for a change from 45C to 25C. Just my inputs; take them for what you will.

Hi guys, i recently reinstalled the aerosoft a320/21 for P3Dv2, sadly it crashes at 0-1% in the loading screen (P3D stopped working). Error report shows the following (partly translated from german) : Name of corrupted application: Prepar3D.exe, Version: 2.5.12945.0, Zeitstempel: 0x55145f5e Name of corrupted Module: Airbus_ECAMD2D.dll, Version: 1.0.0.0, Zeitstempel: 0x551a51e3 Ausnahmecode: 0xc0000005 Fehleroffset: 0x00057f14 ID des fehlerhaften Prozesses: 0x1094 Startzeit der fehlerhaften Anwendung: 0x01d0cd2dc1ec0515 Path of corruped application: D:\Programme\Prepar3d\Prepar3D.exe Path of corrupted module: D:\Programme\Prepar3d\SimObjects\Airplanes\Aerosoft Airbus A…

Hi I have just purchased the above and I have no ND, ECAM (both blacked out) and can not use the CDU (most of the options are greyed out). I have searched the forum for members with the same issue talking about SimConnect libraries that are delivered along with P3D. I don't have anything about this in my within your P3D main folder. I cant find any other information that may help with the issue. Please help!

Hi! What are v/dev? What action do I need to take when v/dev flash in the Primary Flight Display? Best regard kjell wennerholm, sweden

Hello everyone, The A320 has an extremely low PFD refresh rate which renders it unusable for accurate instrument flying. If you don't care about precision flying, it is ok to get along with the 18 fps it provides or whatever. However, it is nearly impossible to vary the attitude just enough to make precise corrections. I'm aware there is another (closed) topic regarding raising the refresh rate value for the PFD. I am an active A32F pilot and I would like to use this aircraft to practice raw data approaches and to stay current on my instrument scanning when I am off for too many days in a row. I believe it shouldn't be difficult to edit the gauge to provi…