PFD, ND, ECAMS

Hi, As can see on photos, there's a bug between HDG and TRK modes. Look: HDG 141, PFD 141, checked - OK. TRK 140, PFD 141, checked - NOT OK.

Hi, When A/SKID turned off in previous versions was an ECAM Memo, this was removed? Or newer versions doens't include this? I remember to see some ecam memo when Anti Skid was turned off.

Hi, I already asked that on HiFi community, but I know some beta testers have the ASN, and maybe can say if it's a ASN issue or not. With ASN I never saw turbulence on weather radar - magenta overlay I know it depends, but still.... Anyone can confirm that appears with ASN? I saw some videos and the magenta turbulence overlay appeared but the weather engine was not Active Sky Next. Thanks.

Hi Together, Purchased the bus a week ago. :-) And as i have a capabel System (5820i @4.7 ghz, win10 x64, 980Ti i thought i can use Hardware rendering for ecam. But when i switch to hardware rendering the displaydriver crashes? When windows "recovers" the driver p3d is closed. With software rendering is active everything is good. Is that a known issiue? Gesendet von meinem SM-G925F mit Tapatalk

I just installed the A318/A319 and no markings appear on both the captain's and first officer's PFD. I appreciate all of your help. 2016-1-14_18-40-25-358.BMP

Good evening, I have the latest A320/321 by Aerosoft and here is my problem: Let's say that my next waypoint is MOPIL at which I have to level-off at FL260 (so VERT REV displays an ALT CSTR as FL260). I then start descent at TOD, I enter 19000ft in the ALT Window and push the knob. I was expecting to see ALT armed in magenta on my FMA (DES engaged) but ALT armed in blue! Check these two photos: As you can see, I have to cross MOPIL at FL260. But: Here, as you can see below my altitude tape, I have selected FL190 (FL190<FL260) but ALT is armed in blue. Normally, my ND should also display a magenta level-off sym…

After a year of using Airbus 320 suddenly the ILS mark on the ND does´t show up anymore, and also the ILS ID on the PFD stays on the same frequency all time, all this after the input of the correspondent arrival. please help. thanks Alberto.

Hi, APPR phase was activated manually but DECEL point still on ND. Thanks

Hello, Can someone please explain the ISA Temp gauge on the lower ECAM? At 35,000 FT I was getting strange numbers such as 0C or +10C instead of the standard -54C. Is it supposed to show the variance from ISA instead? Thank you

First off, happy new year and thank you for reading into the topic! Since 2 days ago, the MCDU of the AFX will not recognise newly created flightplans anymore. The problem has started since installing FlyTampa's EKCH. Since Flightplans from different Flightplanning Tools are not recognised anymore (the MCDU won't offer them as import option and displays 'NONE') I consider it a problem for AFX. Things I've tested: - Doublechecked whether the Filepath for the exported Flightplans have messed up. Answer: No - everything is as always and goes to \Eigene Dokumente\Aerosoft\Aerosoft\AerosoftAirbusExtended\FlightPlans - all AFX Flightpla…

Hello, I have a problem when flying direct to a certain waypoint with the airbus. Basically the plane does not go direct to the waypoint, I will better explain the situation in the screenshots I will show. I was flying the A319 CFM version 1.31. But the problem is present with any of the airbus variants. I was flying to Copenhagen, and VATSIM ATC cleared me direct to waypoint ABEGI, which was not in the database, so in the DIR page of the MCDU I entered the waypoint by using the LAT/LONG format as 5550.5N/01247.3E , is important to consider that ABEGI was not part of my original flightplan. However, the airplane will not fly strictly direct to ABEGI (denot…

As title says, after 5 seconds, the NORMAL vanishes from STATUS page. Is a normal behaviour? Take a look please. Thanks.

Hello Aerosoft. I have am still experiencing the font issue. I am using P3D V3 on windows 10 64 Bit. The issue appears in the A319 and A320 both on V1.31. I have tried this so far. I did a fresh reinstall of the A320 where I went in and deleted all the fonts manually first. I did a restart and cleared the font cache before installing the Bus again (v1.31). I followed the guide on your forum where you first delete the offending font and then adding the one provided in the link (AIRBUSPFD2) I did this before and after reinstalling the bus. Cleared the font cache (both manually and via CC Cleaner). …

Hi, I saw a issue in pitch trim. 2 times pitch 0.0 UP and 1 time pitch 0.0 DN. Check: 0.0 DN 0. 0 UP (look the period is different) 0.0 UP It's something that can be looked?

Hi guys, I am having a problem because the ND and ECAM displays are blacked out. Even when I turn the knob to light them, they remain black. The PFD works well. I am using Windows 7 and P3D V2. I did read the pinned post but installing simconnect did not help! Does anyone have any ideas or passed through the same thing ?

hi all admins and developers.. a new purchased A320-321 extended v1.31 please help.... just only the lower and upper ecams.. http://prntscr.com/9f215a

Hey, since the update to 1.31 the Wx Radar and the Terrain mode not working. Any idea why? Thx and greetings

Hello After the update from 1.30f to 1.31, when I install the "panel" for the VRinsight FCU combo module, the PFD stays black. When i reverse the panel.cfg file, its working again. I know, this is not your problem directly, but maybe you can help me identify what cause this effect. If you need more information, please let me know.

Has anyone had this issue with the A320 before? This is a legitimate copy and the issue has only arisen in the past couple of days and I haven't touched any important files relative to the A320. The Issue is that the lines aren't displaying on the Upper ECAMs EPR, EGT and N1 Gauges.

Hello everyone i recently purchased Aerosoft Airbus A320/321 and the Ecam is blank and the PFD and ND are working.

Knowing the window exists on the A318-321 are always armed, and can only be disarmed by using a special maintenance tool, shouldn't SLIDE always be shown next to the window exits on the ECAM doors page? They go off with the entry doors being disarmed which I'm 95% sure isn't the case IRL, can someone with more certainty confirm?

Once MCDU is fully completed to depart and with a FLEX temp. selected, I set take of power and I see no "MAN FLEX xxº/ SRS / A/THR" blue at the FMA during rolling take off. A/THR doesn´t engage to blue as it should. I have v1.31 new release installed. This problem appears at both A319/A320/A321 aircrafts. This problem didn´t happened at previous release. Thank you!

I'm trying to import a company flight plan but i cannot find the folder that would hold the flight plan. Also when i try to launch the flight planner it seas it cannot find the folder in the directory that it has as default.

Hello all, Since update to OS Windows 10, I've a problem of font with the airbus on fsx and prepar3d v3. I use the 1.31 version and it's the same thing. Thank a lot for your help

Hi, At OP CLB the speed CSTR shouldn't be considerated right, can you confirm? - I'm not sure about this, but altitude CSTR at least shouldn't. I was climbing OP CLB and had a CSTR 220KT and the CSTR was considerated like altitude CSTR on CLB. LEKKO1S at 24 EHAM. PS. Not saying it's a bug, just a doubt. Check: