General questions and discussions regarding Controllers

HI there. I am struggling with my new Honeycomb Bravo throttle and I have been watching a lot of videos about configuration, but things seems to work different on my Bravo. I have also been trying to find a solution in this forum, without any luck. When I am configuring for example the throttle, the handle in the game is only moving halfway, or said in another way, I have to move the handle on Bravo halfway up, before anything happens. It is the same with all the handles that it is possible to configure, propeller and mixture. I am also using the throttle in P3D V4,5 without problems, so I am wondering what I am doing wrong. Hope someone can help …

Suddenly the elevator axis is moving the altitude knob on Autopilot. Uinstalled the CRj and nothing is programmed on the Honeycomb Alpha; unless the elevator. Something wrong. But 110% secure; nothing is mapped on the Alpha axis than the elevator axis. Please help. Carl

I have tried everything i can. I have tried to change the rudder bindings but nothing seems ti steern the nose wheel. I have also turned on the nose wheel strng switch in the aircraft but still i cant steer the aircraft on the ground or even move the rudders at all

Hi, I just got my throttle and pretty much the default set up is doing ok. I only have to change a few things between planes. However, the knob that lets you select values on the right hand side next to the ap button does not change any value at all in ap. Ive went through everything on ap and it changes nothing. But when I check the input value in the options screen it says its bound to plus and minus. Buttons 13 and 14 I think. I did change the vs binding as recommended in a youtube video I saw . But its been the same result before and after . Also I noticed that after I changed the sim rate by pressing r+ theknob then controlled the sim rate just fine. Im sure its jus…

While not as fancy as the HOTAS or Honeycomb, etc...I recently was gifted a Logitech 3D Pro. I'm having trouble with arming thrust reverse and other throttle related items, it seems I need the mouse for most operations. Does anyone else use this hardware for the CRJ, if so can you share your settings? Thanks.

(Altitude) While turning the altitude knob on the Bravo quadrant, the altitude is not changing the altitude in the PFD display. (NAV and HDG) I load a flight plan in the CDU. Take off and gain altitude, set Auto Pilot on, select NAV, and the NAV turns off and goes to HDG. I turn HDG off again, go back to NAV and it goes back to HDG. NAV mode is set to FMS1. Seems like the Honeycomb Quadrant is not in sink with the glare shield panel. Also there always has been problems with the CDU and entering flight plans. I enter a flight plan with SIDs and Stars and end up with waypoints missing or in the wrong location. With the NEW MFSF CRJ, if I make…

This has ben happening basically since last update. AP Hdg light will not extinguish even if Nav hold selected. AP can be on or off same issue. Essentially making AP unserviceable. And Hdg bug changes do not affect plane behaviour. Side note plane lasts less than 5minutes in air. Rolls right and keep rolling until overstressed or hits the deck.

Hi, I installed the CRJ in MSFS2020 and started to study the set up. Using my mouse to pan left, right, up and down I find it only goes a little way and just returns to centre even while holding the right mouse button down or the scroll wheel. It certainly wont stay where I lift my finger. As such I can't even turn on the EFB because it won't scroll that far to the left. I tried another plane and have the same issue though I am only interested in the CRJ. I have the latest update. I have search several forums for a solution but the problem is more unique to the above description. I did change the sensitivity to 100% but doesn't make any difference. Hopefully something sim…

Hello, some things for you to know about the Honeycomb controls: 1. The Honeycomb software installer kills every exe.xml before. A backup will be created - so far as good - and i just found out this strange behavior after my FSUIPC won´t start with the sim anymore. This is very annoying. 2. The AFC bridge module won´t autostart with the sim. It is totally equal which steps are made to solve the issue. For example: The FSUIPC starts with the sim, the AFC bridge does not altough both are entered in the same exe.xml file (and before you give me the answer, i have to check the right path etc. - i have triplecheck alle that things, that you provided to other users wi…

Hi all I use a Honeycomb Alpha/Bravo for flying, but would like to add an additional joystick for ground steering. Is this possible and if so, how would the nosewheel tiller be assigned to the new axis? thanks

Hello there!!! I have a Bravo Throttle Quadrant and I had a couple of issues/concerns/questions that needed to be answered. I will list them in numbered order to make life simpler for all of us. 1)When trying to use the flap lever axis (next to the throttles) on the throttle (instead of the flap lever on the right side) the input seems to be very sensitive. If I move it 1cm it seems to want to extend the flaps by 1. 2)When assigning the right knob to altitude and trying to change it using the left knob it does not change, 3)I cant get any of the lights to work with my corresponding swithces (see attached picture below). I h…

Hi, Well it seems i am having the same trouble as most no lights but this could be due to the fact i cannot install this program. ASUPDATER. Cfg .. not sure what the FONTreg license.txt problem is about? Anyone else had this one before? I have MSFS with a brand new pc.. 2 mths old I can really do with your help as i cannot find anything to get it sorted. BTW also have the Alpha Yoke. thanks mars

Hello, I bought this VRInsight Instrument RadioStack PRO for a previous flightsim, now I have the new version of flightsim and I would like to know if you can help me to find the correct driver and if you can help me to find the correct interface version of FSUIPC, It will be so kind of you to help me. Thank you for your answer.

Hi fellow simmers! Recently, i experience an issue with the hatswitch on my yoke. !- it start to lag, 2- than it stop 3- it come back It is very anoying! Is somebody experience that issue? If so what could i do. I tried to desinstalle the yoke, try to plug on another usb plug, nothing work...

Hello, I'm just configuring the throttle and I did the calibration and use reverse axis and the flaps just beging in Flaps 1 position. Would appreciate some help thanks.

Hello, im having an issue with the LED Lights, they aren't working when i am launching up the game or even when trying to fly, i have installed the latest drivers and i also have my EXE file which is here. exe.xml

Hello ... I am slightly struggling to set up the switches on my Bravo unit as when I try to set a item such as the Parking Brake or fuel pump, using the Toggle function on a switch, it keeps turning on/off repeatedly? For example against "Toggle Parking Brake", I set buttons 46 and 47 (the last switch on the panel), but when I enter the sim the parking brake engages and disengages constantly. I find the same for fuel pump, and haven't gone any further? Also the LEDS on my Gear up/Down are not lit ... can this be caused by the same issue??

Hello i just got my bravo . Downloaded the driver from your site installed it start up sim and led are on but my sim crashes . I tried 4 times and i get this error . Please see attachment . Is there a fix for this.

Hello, Got error on install. MSFS steam version and is installed another user not admin. Any help? juha

I have found if I load the sim and set up a flight the lights don’t work on the Throttle … SO while the sim is still active I open my community folder and open the AFC-Bridge folder THEN I open the bin folder and click on the AFC_Bridge Application …This kick the application into working …I then close the open flight in the sim and start a new flight and the lights then come on …YIPPEE …I have to do this every time I boot up MSFS but once it is up and running for the day the lights stay working until the next time …I created a shortcut to the Community folder on my 2nd monitor desktop.

Hi - I used the installer to install the honeycomb bravo led light enabler for MSFS. On startup, I'm getting an afc bridge error and the led lights are not working. I can't seem to find any documentation on how to fix.

when I shut down MSFS I am getting an AFC Bridge dialog error message Simconnect failed to CallDispatch Everything seems to be working, just getting that message. Thanx, Vic

I've set up my Flight Combo for MSFS and have 2 questions to ask? First as I'm a Private Pilot the tension on the Alpha Yoke is a lot stronger than any yoke in any plane I have ever flown. Is there there any way to lessen the pressure on this yoke or does a guy have to lift weights to over come the yoke. and the 2nd question when I tried to bind the Parking Brake on the Bravo Switch for the C152 and C172 the Brakes moved on there own. It first disengages and then engages then disengages I watched for 2-3 min. just clicking off and on.

Hi, I tried to install the MSFS driver several times now. I receive this error message: In ASUpdater: AS Honeycomb: The server version file could not be loaded! http://update.aerosoft.com.dedi2593.your-server.de/asupdater/as_honeycomb_msfs/asupdater.xml System.Net.WebException: The remote server returned an error: (404) Not Found. at System.Net.HttpWebRequest.GetResponse() at System.Xml.XmlDownloadManager.GetNonFileStream(Uri uri, ICredentials credentials, IWebProxy proxy, RequestCachePolicy cachePolicy) at System.Xml.XmlDownloadManager.GetStream(Uri uri, ICredentials credentials, IWebProxy proxy, RequestCachePolicy cacheP…

I see there is a update for the led's to work on MSFS. I ran the update but no led lights.