General questions and discussions regarding Controllers

Hi there, does anybody out there know how to correct left-leaning tendency with the Honeycomb Alpha Yoke and MSFS 2024? I hear that I should be able to fly at cruise "hands off" for at least 10 seconds. Currently, with the Yoke in center position, I move left from 360 degrees, 359, 358 etc.... and the only way I can keep the yoke even is by pressing on the left side of the yoke very slightly with my left ring-finger or pinky and holding it there. I have heard that this is not a P-factor issue at cruise and it should fly straight. I have tried to fix the problem by going under "game controllers" in Windows and moving the center circle slightly to the right but t…

Good morning all, I have a problem when I click on AFC Bridge in community in FS2020 I have this message that appears failed to initialize Simconnect to the line and I cannot run it. How to solve this problem please Thank you Pierre

I am planning to use 6 Instrument Panels and I have already experienced that those 6 Instrument Panels connected to the same USB 3.0 active hub with 10 sockets power via the USB connection The hub can supply 12Vx3A or 36W. Each panel seems to need 5Vx0,5A or 2,5W so that 6 Instrument Panel need 15W. When I did plug the 6 Panels to the same hub, just need less than 50% of the power the hub can deliver they partly stayed off. Does anybody have experience connecting 6 Instrument Panels to a single hub? [img]https://live.staticflickr.com/65535/53796666801_0aaec37945_z.jpg[/img]

How do you make the lights work?

The reverse switches at both ends of the small reverser levers do not show up in windows calibration screen as the other buttons do. Therefore they do not function in MSFS 2024. The 2024 driver for lights has been downloaded and all other functions seem to work. AFC Bridge is installed. Don't know what to do.

Not sure if this happens after installing new FS2024 software or what, but at this point the only funtion that's working on the yoke is the actual yoke, no camera no electric trim. is there a video that can shown me how to reset this on youtube. I did a research, but I can only find videos for the throllle. Any help is greatly appreciated. Thank you Adib

After installing the latest honeycomb bravo driver, I can no longer control the autopilot on the C90 with either the bravo, or by using the mouse. This fault only occurs in career mode. Any advice? I've uninstalled AFC bridge and re installed MSFS 2024, problem persists.

Hello, I have just installed Honeycomb installer, and he said me he can't find miscrosoft flight simulator. MSFS 2020 in my system is here: My name/ AppData/ Local/ Microsoft.FlightSimulator_8wekyb3d8bbwe/ and after i have this folder: AC AppData LocalCache LocalState RoamingState Settings SystemAppData TempState It's microsoft store version. Thankl you for your help. Happy new year. Best regards, Didier

I've been using my Bravo controls for a while now. This week, Throttle1 and Prop1 are not going to full throttle. I've tried uninstalling both Programs(2020 and 2024) to make sure there isn't a conflict. I've re-installed 2020. All Bravo profiles are still existing. This is very frustrating. Please Help.

I can gAFC_Bridge.pdfet the Honeycomb Bravo autopanel to work in MSFS 2024. What is wrong? (see attached files) Any help is appreciated. kind regards Alex

Hi everyone, I recently got both the Honeycomb Bravo Throttle Quadrant and Alpha Flight Controls, and I was met with an error when trying to install the Drivers. I always get the error "Missing user.cfg". I discovered the origin of this problem came from the fact that MSFS was not installed on the admin account. I found another thread with the same issue, which I'll link below. After a bit of discussing, the user having the problem was provided with a special installation to solve this problem. This seemed to work for the user, unfortunately the link to the software doesn't work anymore. Would anyone know how to access …

Hi all, I'm having trouble getting my Honeycomb Bravo Throttle Quadrant to work with MSFS 2020 on PC Game Pass. I also have an Alpha Yoke, which is working fine. I've installed the latest drivers for both devices (as administrator), and I can see both devices in Windows Device Manager. However, when I go into the MSFS 2020 controls settings, only the Alpha Yoke shows up. The Bravo Throttle is not detected at all. I've tried the following troubleshooting steps: * Different USB cables * Different USB ports * Reinstalling the drivers * Unplugging and replugging the devices * Restarting my computer Nothing seems to work. Has anyo…

Dear fellow simmers, I am scratching my head with a "problem": I decided to treat myself and finally my honeycomb bravo throttle arrived. Super happy and all the keys are configurated and working. I am having problems with the lighs instead. I am looking at the web and it appears to be a common issue with a solid line to troubleshoot it. (For istance I followed also: However, of course I am special and things work differently for me! AFC_Bridge Installed almost all the lights work but random lights appear in the annunciator panel Better Bravo Light Installed (after the AFC Bridge attempt) More…

Bonjour , l octavi IFR-1 fonctionne t il sur tous les GPS des avions ?merci

If your Honeycomb Alpha XPC yoke require internal calibration (not the operating system level one), you can now use the standard procedure described in the tutorial below. Two important points : 1 - The calibration can be performed either with a PC or an Xbox That procedure only requires the yoke to be connected to a power source, whatever that source is. 2 - You first need to set the yoke in PC mode. It will NOT work in Xbox mode. If you are using an Xbox don't forget to set Xbox mode after the calibration procedure has been performed !

You would think that when you change hundreds of dollars for a product, you would try to provide something that is at least somewhat ready to use. Unfortunately, it seems like the developers on the Honeycomb Alpha and Bravo expect their customers to just figure it out and spend hours configuring their product. This is not acceptable. They tout the interchangeability of the throttle, but do not offer different profiles for the different configurations. That's unacceptable. I'm on the verge of returning these products because of how frustrated and disappointed I am.

Hello for two days no longer able to use the control of the landing gear of the honeycomb well done with all the avians impossible to reassign it in the control parameters of the game via recognition by activating the lever and this day by wanting to launch a flight with the pmdg 737 certain key of the mcp (LVL CHG, HDG SEL, LNAV, VOR LOC and APP) did not stop relying all alone and at the same time, I thought that it was due to the update of pmdg which had been done just before this problem arose but on the pmdg forum he told me that the problem did not come from the last update, and I also took a screen of the commands in the parameters linked to the AP qu remains in pre…

ive been watching videos and i still cant find anything interestingf or helpful.

Hello, I’ve Honeycomb Alpha and Bravo. I use in MSFS 2020. No problems with Bravo and lights ont alpha. But, I can’t program buttons on the Yoke of Alpha. Impossible obtain the vews with thre Hat. Impossible use others buttons ont the yoke. Havez-you an idza to hep me?? Thank’s.

Good morning, My AFC_Bridge.exe does not load itself when the client loads, I have attached my exe.xml. I have followed all of the steps suggested in this other thread, Like others in that thread, if I manually load the plugin once the simulator is running it works after I reload the flight, but it doesn't auto-load on startup. I have the Windows Store version via the XBOX Game Pass. I have followed the steps of reinstalling, deleting the exe.xml and reinstalling, installing as an admin and without, still nothing. exe.xml

Hi, I have a problem. I got a new laptop and i am trying to setup the Bravo quadrant. As you can see in the picture below (sorry for two screen SS), it is recognized my MSFS as 6-AXIS 48 BUTTON DEVICE. Is this normal?

Hi all, Anyone there who has a good Helicopter configuration for this stick in MSFS . Thanks sofar Geert Burgstra

Hello, I just purchased a Honeycomb Alpha Yoke and Bravo Throttle Quadrant through Amazon and I'm using these on MSFS 2020. The yoke works perfectly. However, the Bravo quadrant does not seem to power on or is even recognized on Windows as a new device. I've tried plugging into other laptops I have and switching the Alpha and Bravo cables to see if it's the wire, but still no luck. I'm not 100% sure if I have the driver installed for it? Since I downloaded the one on the Honeycomb website, but it only gave me the ASUpdater and I can't seem to find a link that gives me the configurator that I see in all of the screenshots. Also, I tried downloading the christmas tree teste…

I have spent the last 5 hours trying to get my Bravo Throttle Quadrant to work properly. Here are the issues I'm experiencing: 1. Throttle Axes Are Incorrect Notes: When I open the X-Plane 12 configurator and try to calibrate the levers, this is what it looks like. Lever 1 is Lever 2 Lever 2 is Lever 1 and the rest of the levers are fine and on the correct axes. To fix this I just reassigned the levers so that they would increase/decrease the correct control, but this did not change the axis they were on. The Main Problem LEDs and FCU Selector Along with the Incr/Decr Knob not working at all Notes: As I said befor…

I was wondering if anyone can help me. My throttle’s do not work within the game anymore. They are very jittery and do not do it anything like they’re supposed to. my throttle’s do not work within the game anymore. They are very jittery and do not do it anything like they’re supposed to.. Everything has been working fine for a year and all of a sudden my throttles do not work on any plane in MSFS. I have not added anything to the community library or anything like that . I have not added anything to the community library or anything like that. The only thing that I noticed different in the last month or so is that one of the throttle’s makes a squeak sound...SEE VIDEO...I…