StuartBBN135 1 Posted October 14, 2018 Share Posted October 14, 2018 Now I know how Sully felt!!! Link to comment Share on other sites More sharing options...
por928 65 Posted October 24, 2018 Share Posted October 24, 2018 Umm, and I thought I had done something....On a long flight BAW2, KJFK-EGLC with the A318(BA Livery) and just short of Shannon, I just lost all power including electrics, in the night with nothing on the screens....A tad scary, as no RAT, no emergency power. I first noticed pack 2 fault, then pack1 then the gens off line...sort of like fuel starvation, though FOB=7280kg... But after descending from FL380 through 9000, all of a sudden, everything came back to life..Though, the flight plan was lost. Now diverting to EGAA and will land here and give most of my passengers some Valium, then re-schedule the flight later today. First time ever this happen with the buses. Link to comment Share on other sites More sharing options...
abic 0 Posted October 28, 2018 Share Posted October 28, 2018 I reported a similar situation in the general discussion a few days ago, with total power loss and dark cockpit displays on managed flight MKJS-TNCM in the phase of starting descent. I tried to replicate this today again with the same managed flight on A320 and made sure that more than enough fuel was on board. It happened again on descent after app. 2 h flight time at altitude of ca. 30000 feet. Again total loss of power and displays as described before. Recovered the situation by Autosave, everything working at app. 2 minutes before failure, I got out of managed flight to hand flying, AP, ATHR etc. off. At the same time of the saved flight the power loss etc. happened. What is the problem or solution? Link to comment Share on other sites More sharing options...
abic 0 Posted October 28, 2018 Share Posted October 28, 2018 Add to my post after reading others: have no ezdock but Saitek X52. but even haven't ouched the stick when the problem happened on the managed descent. Thanks, Bernd Link to comment Share on other sites More sharing options...
por928 65 Posted October 29, 2018 Share Posted October 29, 2018 6 hours ago, abic said: Add to my post after reading others: have no ezdock but Saitek X52. but even haven't ouched the stick when the problem happened on the managed descent. Thanks, Bernd I was in cruise at FL380, some 5 hours into a 7 hour flight(KJFK-EGLC) with no action on the stick(Logitech Extr 30 Pro, using Chaseplane. I notes there are several posts scattered about the forum. To me, it is like the aircraft has run out of fuel and flattened the batteries (despite loads of fuel on board) the aircraft systems just shut down, in my case, the packs went, then the gens then a few moments later, all black. When I was just getting out the life jackets, when at about FL120, she came back to life, with no FMS loaded... Link to comment Share on other sites More sharing options...
klisura 92 Posted October 29, 2018 Share Posted October 29, 2018 Yesterday I flew from LEBL to LIRN and while I was setting MCDU at the gate I noticed a strange thing: I have generated the loadsheet in the fuel planner and made an instant load. 9.2 kg FOB. Then I set the Block fuel data by pressing the LSK and appears 2.4 instead of 9.2 (I checked on the ecam that FOB was 9.2) At that point I manually changed that 2.4 in 9.2 So I was wondering if this bug happened to me yesterday could cause your engine off during the flight but I don't think so, the fob was correct... Has someone else experienced the same bug? Link to comment Share on other sites More sharing options...
abic 0 Posted October 29, 2018 Share Posted October 29, 2018 I tried today to recreate my flight MKJS-TNCM at the point where the A320 had the total loss of power. I booted the PC up and started P3Dv4.3 as usual by loading the autosaved situation shortly before the power loss (enroute, app. 28000 feet on descent, flightplan powermanaged by AP, ATHR, FD, flight time app. 1:50 h). Total power loss and all displays dark (as described) after 1 minute, plane goes in powerless descent, exterior view shows turbine blades are only rotating in "idle", no jet sound. pushing buttons and switches no effect, no activation of gear, spoilers, elevators etc., no nav lights or strobes like there is absolutely no electric or hydraulic power. The MDCU 3 is mostly greyed out, no change of state or other action possible. After the plane crashes in the sea and bounces back (2 times) suddenly jet engines start running and the AP Display (FDU?) lights up again, PDF, ND and EICAS displays stay still dark. Throttle input is possible. After app. 30 seconds I stopped the simulation. I hope this description gives some hint what could be wrong. Bernd Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted October 30, 2018 Aerosoft Share Posted October 30, 2018 Can you send us that autosave file? Link to comment Share on other sites More sharing options...
stevieb94 0 Posted November 3, 2018 Share Posted November 3, 2018 Hi, i've had the same issue, wizzair a320 UK2000 EGCN, ORBX VERCTOR GLOBAL, full power loss when establishing ILS, aircraft turns into a glider and falls out the sky, the systems come back on after 30 seconds of falling. however all MCDU data deleted and its asif the aircraft loaded back up into a takeoff state.  I'm starting to get annoyed as its the third time in two weeks its happened. Thanks, Link to comment Share on other sites More sharing options...
Emi 5161 Posted November 4, 2018 Share Posted November 4, 2018 For everyone experiencing this: When the failure happens, could you open the P3D Fuel and Payload dialogue and take note of your fuel values in each tank? Link to comment Share on other sites More sharing options...
ozgulkagan 18 Posted November 5, 2018 Share Posted November 5, 2018 I had this only once, on cruise. A321 IAE.  No addons except Aerosoft Airbus, just some freeware scenery airports. No weather addon etc. I was online at IVAO. Don't remember the exact route.  The only thing I can say is, I clicked ECAM FLT Controls page, then closed it, after a few seconds both engines lost all power for one or two seconds, then came back. Link to comment Share on other sites More sharing options...
swisspilotace 6 Posted November 6, 2018 Share Posted November 6, 2018 Twice today on approach into Zurich. No issue and both times ober 4000kgs FOB left. Always happend when descending through FL130. Saitek joystick in use, however did not touch anything. I will inform if it happens again tomorrow. Really frustrating though. 1x with A321 1x with A320 So it seems to happen on all aircraft. Â Regards Luca Link to comment Share on other sites More sharing options...
swisspilotace 6 Posted November 6, 2018 Share Posted November 6, 2018 On 4.11.2018 at 10:43, Emanuel Hagen sagte: For everyone experiencing this: When the failure happens, could you open the P3D Fuel and Payload dialogue and take note of your fuel values in each tank? I will do so, the next time it happens. Link to comment Share on other sites More sharing options...
cloose 18 Posted November 7, 2018 Share Posted November 7, 2018 And it probably also makes sense to report if you have anything assigned to any mixture control axis. There are similar reports for other aircrafts: Â Â Link to comment Share on other sites More sharing options...
Aerosoft Aerosoft Team [Inactive Account] 51558 Posted November 8, 2018 Aerosoft Share Posted November 8, 2018 Please follow up here:Â Â so we can keep track of this issues. Link to comment Share on other sites More sharing options...
timothyj6769 2 Posted December 10, 2019 Share Posted December 10, 2019 This happened to me mid flight at 37000 I just lost all power. A320 Professional. Nothing worked to get power back on. Ended the flight . Â Link to comment Share on other sites More sharing options...
Deputy Sheriffs Secondator 643 Posted December 10, 2019 Deputy Sheriffs Share Posted December 10, 2019 Do you have any Carenado aircraft installed by any chance? Were you flying online? Link to comment Share on other sites More sharing options...
DaveCT2003 2553 Posted December 10, 2019 Share Posted December 10, 2019 I don't, and it still occurs rarely and randomly, as I've posted in the Beta area. Â Link to comment Share on other sites More sharing options...
Trevor Hannant 126 Posted December 11, 2019 Share Posted December 11, 2019 I've now had this on both A330 flights I've tried this week but have not (yet!) experienced this in any other aircraft. Â As I've only just come across this topic, I've no idea whether a Carenado aircraft was called as AI or not at the time however leaving the APU running in flight allowed the flight to carry on uninterrupted pending finding the root cause. Link to comment Share on other sites More sharing options...
Trevor Hannant 126 Posted December 11, 2019 Share Posted December 11, 2019 Popped online in Greenland (no traffic!) and left the 330 running engines on there for an hour - no issues. Â Have removed Carenado aircraft from Model Matching rules in my vPilot install and will try a flight again with traffic to see if the issue re-occurs. Link to comment Share on other sites More sharing options...
Trevor Hannant 126 Posted December 14, 2019 Share Posted December 14, 2019 I've removed Carenado aircraft from my model matching but once again had the issue.  When this had happened before, I turned the APU on and left it on however despite trying to run the flight with the APU on, I still experienced a packs cut off, then engines before losing electrics. Link to comment Share on other sites More sharing options...
DaveCT2003 2553 Posted December 14, 2019 Share Posted December 14, 2019 Guys,  When this happens, would you please take a look at the P3D Menu\Vehicle\Fuel and Payload screen and take a screen shot and post here?  Now absent of any zero fuel condition inside of P3D (which is why I asked you to check above), we had several customers report this back with the A320 Professional and we asked them to completely unistal and reinstall P3D (this includes manually removing all P3D folders from the install location, ProgramData, and AppData folders) and reinstall. As I recall, the problem never returned for them. I think Mathijs can back me up on that.  The question might come up... Why doesn;'t this occur with other aircraft? The reason is that our airliners are the only ones in P3D I'm aware of that use the P3Dv4.5 compilers, making them truly native P3Dv4.5 aircraft where the others are not. This being the case, it's understandable that you might not have this issue with other aircraft.  Many thanks!  Link to comment Share on other sites More sharing options...
Trevor Hannant 126 Posted December 16, 2019 Share Posted December 16, 2019 OK, had a nearly successful flight and grabbed a few screenshots.   Was in the descent so engines idle when I got the Packs Off indications. Quickly fired up the APU but still lost power. Grabbed a screenshot of the fuel state at the time the engines died:  Please login to display this image. Please login to display this image.  Restarting the engines gave me thrust again to complete the landing with APU powered on. Link to comment Share on other sites More sharing options...
Deputy Sheriffs Secondator 643 Posted December 16, 2019 Deputy Sheriffs Share Posted December 16, 2019 Hello Trevor, could you please enable logging and zip the whole Data folder here next time you see this issue. Even better if you can give the timestamp when the issue happened. Link to comment Share on other sites More sharing options...
Trevor Hannant 126 Posted December 16, 2019 Share Posted December 16, 2019 Had enabled it just in case but wasn't sure what data you needed. Â Time of the screenshots was around 20:20z so I'd imagine in the 5/10 mins just before then. Â Thanks! Data.zip Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.