niallkav

mid flight or taxi power loss

Recommended Posts

Hi M,

I am not angry by the way (as you suggested- I have no idea how you came to that conclusion - precisely the opposite) but enthusiastic about your product and trying to help me and others (and perhaps you?)...

so... again

multiple sudden black screens on taxi or while in flight. pfd mfd ecam… all. in taxi engines also fail. no xx.xxx but temp readings look like fuel failure. possible to recover after APU restart (OVHD buttons also inoperative so this is a guess) then APU bleed the E2 E1. FMS data all lost.

 

in flight (separate to above and independently) the same can occur, but engines "sound" (remember no ECAM) ok.

 

P3d v4 orbx fsaero linda asx v4 

 

 

Niall

Share this post


Link to post
Share on other sites
2 hours ago, niallkav said:

Dave,

Yes carenado SF34. I should delete?

Niall

 

No sir, unless you don't fly it anymore.  There is a fix for this in their forums... basically, it's their copyright protection causing a CTD if their texture is called for an AI Aircraft.

 

Best wishes.

 

  • Upvote 1

Share this post


Link to post
Share on other sites

Hi again,

Just had the same event: power loss on entry into runway (LSZH vatsim). A320 just installed and 1.2.0.1 version. no carenado aircraft.

ideas?

Niall

Share this post


Link to post
Share on other sites

We have no idea on this right now. We hope we will get a reliable scenario so we can recreate this and see what variable is set.

Share this post


Link to post
Share on other sites

THX M,

unistalled 318 320 and the re-installed P3D v4.3 (just Client !). also removed RAAS, both locked and unlocked (I have an unlocked RAAS...).

have ORBX and LINDA

ALSO removed Ultimate traffic as my AI and installed FLAi (Boston FIR offering).

so far so good...

Niall

 

Share this post


Link to post
Share on other sites

ok,

after all the above I just had power failure at Gatwick on taxi after arrival... left me on the rwy!

niall

Share this post


Link to post
Share on other sites

Hi Guys,

And again while VIAINTERCITY Edinburgh LFPG... 

Thoughts? had plenty of fuel.

Niall

Share this post


Link to post
Share on other sites

We have absolutely no idea on this.  we just hope to get enough information to recreate it.

Share this post


Link to post
Share on other sites

THX M,

I will keep experimenting here too. incidently I cannot find any information on the MCDU weather options? I use Active X...

 

Many Thanks

Niall

Share this post


Link to post
Share on other sites
vor 35 Minuten, niallkav sagte:

I cannot find any information on the MCDU weather options? I use Active X...

Please open a separate topic on this.

Share this post


Link to post
Share on other sites

Hi M,

I may have found my problem Sir. I have a Saitek Pro with throttles and I have mixture and propeller axes (for a turboprop..) assigned in P3D. I also had automixture off. putting mixture and prop full/100 and setting automixture to auto in p3d I may have solved it. I will confirm after a few more flights M.

Kind Regards

Niall

  • Upvote 1

Share this post


Link to post
Share on other sites

Today i have two of this Problems

 

mid taxi power loss.

 

1. First flight with A320 CFM (V.1.2.1.0) power loss (JS EDDH to LIPZ) at taxi to RW 33. Second flight without Problems.   (Repaint Condor)

2. First flight with A319 CFM (V.1.2.1.0) power loss(JS EDDH to LEVC) at taxi to RW 33. Second flight without Problems.  (Repaint LH 2018)

 

The Engines are running mid power les all the time

 

 

I have no Corenado planes.

I have Saitek Hardware to fly.

 

Sorry about my bad eglisch writing.

Better to write in german.

 

Frank from EDDM

Share this post


Link to post
Share on other sites

Ahhhh now THAT is good info as we at least see a pattern here. Did you do anything special while taxing?

Share this post


Link to post
Share on other sites
I was just walking and thinking about the mistake.

I set up my ezdoc cam before each flight where the error occurred.
After updating to 1.2.1.0 I always had to change something.
The second flight has always worked because I have changed nothing more on the Ezdoc Cam.
The first flight was the 320 and the second was the 319
To program the cam I use the key (E)
I have to press (E)to start the programming and then (E) again to finish.
Maybe the error comes from this button.
Have now changed the key to (+)
That's just a guess
 
One Question more. In my FMC the ZFCG is not working. Always orange Boxes.

Frank

Share this post


Link to post
Share on other sites
2 hours ago, f.skywalker said:
I was just walking and thinking about the mistake.

I set up my ezdoc cam before each flight where the error occurred.
After updating to 1.2.1.0 I always had to change something.
The second flight has always worked because I have changed nothing more on the Ezdoc Cam.
The first flight was the 320 and the second was the 319
To program the cam I use the key (E)
I have to press (E)to start the programming and then (E) again to finish.
Maybe the error comes from this button.
Have now changed the key to (+)
That's just a guess
 
One Question more. In my FMC the ZFCG is not working. Always orange Boxes.

Frank

 

 

Hello Frank,

 

We and other developers have seen problems caused by EZDoc that at first one would never believe that EZDoc was the culprit, but it turned out it was. 

 

Regarding your ZFCG value, are you double clicking the LSK (Line Select Key) next to the ZFCG entry or entering the value manually?

 

By the way, we often see people refer to an MCDU as an FMC, so I created a post (see below) that helps explain this a little better.

 


 

 

 

 

 

Share this post


Link to post
Share on other sites

I will test it the next few days if I have time.
Of course, I'll tell you the result of my test.


After only one user had the problem synonymous.

Can also be a small bug in the Airbus.

 

 

Frank

Share this post


Link to post
Share on other sites

Hallo Dave and  Mathijs

 

I just wanted to report that at the moment no flights
more errors have occurred with the power loss Problem.
I think that it probably had to do with my Ezdoc setting Keys and the Bus..

After i change my Settings in Ezdoc i have no Problems.

Ezdoc works perfect with my  Airbus Prof.
If there is an error again I will report it.

 

Frank from EDDM

Share this post


Link to post
Share on other sites

I too had a total power loss in the A318 (BA livery) on flight EINN-KJFK. Just abeam Boston approx 40 miles TOD. The FOB showed 2.8 tonnes and there had been no issues during the 6 hour flight. I dont use Ezdok in P3D v4 and scenery is default. First indication was N1 in the ecam oscillating up and down. Electrics,Apu and start switches no response. Not even the battery switches.

Have flown busses since the original airbus extended and never seen this before.

Very strange.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now